Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for MACGREGOR Legacy Series
- Page 1 INSTALLATION INSTRUCTIONS SMALL BASEBALL SCOREBOARD Model MSB3003L5CP...
-
Page 2: Table Of Contents
TABLE OF CONTENTS DESCRIPTION INSTRUCTIONS FOR REPORTING SHIPPING DAMAGE INSTALLATION OVERVIEW PRODUCT SPECIFICATIONS DETERMINING LOCATION AND ORIENTATION INSTALLING MOUNTING POLES OR I-BEAMS MOUNTING THE SCOREBOARD INSTALLING THE SPORT PANELS ATTACHING THE CRISS CROSS BATS RUNNING AND CONNECTING THE CONTROL CABLE RUNNING AND CONNECTING THE ELECTRIC SERVICE TESTING THE INSTALLED SYSTEM WARRANTY ACTIVATION... -
Page 3: Description
DESCRIPTION SMALL BASEBALL-SHAPED SCOREBOARD NOTE TO INSTALLERS: PLEASE RETURN THIS MANUAL TO THE INDIVIDUAL IN CHARGE OF THE SCOREBOARD UPON COMPLETION OF INSTALLATION. The scoreboard and all accompanying accessories have been carefully inspected and tested before leaving the factory. However, it is possible for damage to have occurred during shipping so we ask that you inspect all shipping containers upon arrival for damage and ensure that you have all of the parts listed below. -
Page 4: Installation Overview
INSTALLATION OVERVIEW This manual will walk you through the installation of the scoreboard. While care has been taken to consider the many scenarios for installation, some general information applies to all. Use this guide as closely as possible to ensure proper installation, as follows: 1. -
Page 5: Determining Location And Orientation
DETERMINING LOCATION AND ORIENTATION The scoreboard should be positioned so that the greatest number of spectators can easily view it. Also, consider the best orientation of the scoreboard should the system be used to score a daytime or afternoon game. The scoreboard should be positioned so that sunlight does not glare off of its face. In the U.S., placement on the South or West side of the field is recommended. -
Page 6: Mounting The Scoreboard
CABINET. CONTROL MODULE, POWER, AND SIGNAL CABLE CONNECTIONS ARE ACCESSED ON THE BACK OF THE SCOREBOARD MOUNTING THE SCOREBOARD NOTE: IF THE POLES/I-BEAMS ARE NOT IN ALIGNMENT --- SHIMS MAY BE NEEDED TO MOUNT THE SCOREBOARD PROPERLY. MOUNTING THE SCOREBOARD WITH THE POLES/I-BEAMS OUT OF ALIGNMENT MAY DAMAGE THE SCOREBOARD AND VOID THE WARRANTY. -
Page 7: Installing The Sport Panels
INSTALLING THE SPORT PANELS Parts List: 4 - Sport Panels 4 - 15” braces (2 each / for top and bottom panels) 4 - 8” braces (2 each / for side panels) 2 - ¼” 20 x 1” bolts 16 – 3/8” x 1 ½” bolts 32 –... - Page 8 2. Install one ¼” 20 x 1” bolt at each end of the top Sport panel and install two 15” support braces on the back side of the panel. The support braces bolt to the back of the Sport panel and to the top flange of the scoreboard using 3/8”...
-
Page 9: Attaching The Criss Cross Bats
ATTACHING THE CRISS CROSS BATS PARTS: 1. 2 handles with attached braces 2. 2 barrels with attached braces 3. 4 braces look like a triangle with studs for mounting the bats 4. (4) ¼”/ 20 wing nuts approximately 32 5. Self tapping screws... - Page 10 Installation: 1. Place two of the angle brackets on the top outside corners of the scoreboard and attach with the hardware appropriate bolts and tex screws. 2. Attach the barrels of the bats to the respective sides using the wing nuts attach the base of the barrels to the angle brackets.
-
Page 11: Running And Connecting The Control Cable
RUNNING & CONNECTING THE CONTROL CABLE (For scoreboards with Wireless Remote Control, skip this step.) The control cable must be run in a separate conduit than is used for the electrical service. The control cable should run from the scoreboard to a location that is within 10 feet of the scorekeeper’s location and into a 2”X4”... - Page 12 THE BLACK, GREEN, AND WHITE WIRES ON THE BACK OF THE WALL PLATE AT THE SCORING LOCATION. At the scorekeeper’s location: 1. With the communication cable installed between the scoreboard and the 2”X4” wall box, locate the wall plate provided with your installation hardware. 2.
-
Page 13: Running And Connecting The Electric Service
6. Inside the scoreboard, connect the control cable leads to the appropriate terminals on the terminal block, according to the label above the terminal block. NOTE: Refer to the connections that were made at the scorekeeper’s location. Make the connections at the scoreboard match the connections at the scorekeeper’s location. 7. -
Page 15: Testing The Installed System
TESTING THE INSTALLED SYSTEM NOTE: Please refer to the OPERATORS MANUAL on the CD, or included with the system to operate the scoreboard. Connecting cable-controlled systems: Connect one end of the supplied 20-ft. control cable into either of the two control cable jacks on the back of the controller and the other into the receptacle on the supplied junction box cover installed at the scorekeeper’s location. -
Page 16: Warranty Activation
IMPORTANT Warranty Activation/Installation & Completion Sign Off Sheet NOTE: This sheet must be completely filled out and returned/faxed (270) 753-3773 to Scoreboard Service Company before your warranty can be activated. Your Serial Number _______________________________________ Your Model Number _______________________________________ Date Purchased _______________________________________ Sales Agent _______________________________________...