Summary of Contents for Siemens SIMATIC 8DO 24 V DC/0.5 A HF
Page 1
Properties ______________ SIMATIC ET 200S distributed I/O Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0) ______________ Parameters ______________ Diagnostics SIMATIC ET 200S distributed I/O Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00- 0AB0) Manual 10/2009 A5E02515349-01...
Page 2
Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
Properties Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00- 0AB0) Properties ● Digital electronic module with eight outputs ● Output current 0.5 A per output, aggregate current 4 A ● Rated load voltage 24 VDC ● Diagnostics: wire break ● Short-circuit protection ●...
Page 6
Properties 1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0) General terminal assignment Note Terminals A4, A8, A3 and A7 are only available at specified terminal modules. Terminal assignment for 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0) Terminal Assignment Terminal Assignment Notes : Output signal, Channel n •...
Page 7
Properties 1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0) Two-wire connection The following configuration example shows a 2-wire connection with the electronic modules 8DO DC24V. You require further terminals so that sufficient terminals are available for the chassis ground connection M when the TM-E15S26-A1 terminal modules are used. In the example this is implemented by the add-on terminal TE-U120S4x10 that can be mounted as from a width of 120 mm (8 EMs).
Page 9
Properties 1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0) Technical data 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0) Dimensions and weight Width (mm) Weight Approx. 40 g Module-specific data Supports isochronous operation Number of outputs Length of cable Unshielded • max. 600 m Shielded •...
Page 10
Properties 1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0) At "0" to "1" • max. 300 μs At "1" to "0" • max. 600 μs Load resistor range 48 Ω to 3.4 kΩ Lamp load max. 5 W Connecting two outputs in parallel For redundant triggering of a load •...
Parameters Parameters This table shows the parameters for the digital output modules: Table 2- 1 Parameters for digital output modules 8DO DC24V/0.5A HF Range of values Default setting Applicability Substitute a value Response to CPU/master • Substitute a value Module STOP Retain last value •...
Diagnostics Diagnostics using LED display LED display ① Group error (red) ② Status display for output status (green) Status and error displays Event (LEDs) Cause Remedy No configuration or incorrect module Check the parameter plugged in. Diagnostic message. settings. Evaluate the diagnosis.
Diagnostics 3.2 Error types Error types Digital electronic module error types Table 3- 1 Error types Error type Meaning Remedy 11010: External error Short circuit (on at least Correct the process wiring one channel) Diagnostic message will be issued on channel 0. "Short circuit" is only reported in the switched output state.