Advertisement
Step 4 — Run Cables Between Units
Connect the rear panel transmitter output to the rear panel receiver input using twisted pair cable.
For optimal performance, Extron highly recommends the following:
RJ-45 termination with CATx cable must comply with TIA/EIA T 568B wiring standard for all connections.
For more information on TP cable wiring and termination, see the full product user guides at
www.extron.com.
Use shielded twisted pair cable, 24 AWG solid conductor or better, with a minimum cable bandwidth of 400
MHz.
ATTENTION:
•
Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable.
•
N'utilisez pas le câble AV Skew-Free UTP version améliorée UTP23SF d'Extron ou le câble STP201.
Use shielded RJ-45 plugs to terminate the cable.
Limit the use of RJ-45 patches. Overall transmission distance capabilities vary depending on the number of patches used. If possible,
limit the number of patches to only 1 or 2 total.
If RJ-45 patches must be used in the system, shielded CAT 6 (or better) patches are recommended.
Step 5 — Connect Outputs from the Receiver
DVI or HDMI output connector — Connect a DVI or HDMI cable between this port and the input port of the display.
Audio output — Connect a stereo audio device to this 3.5 mm mini stereo jack to receive the
passed through unbalanced audio.
RS-232/IR Pass-Through connector — Plug an RS-232 or modulated IR device into the
RS-232/IR Pass-Through port. Wire the connector as shown for step 3.
Step 6 — Power the Units
Wire the 2-pole captive screw connector for the included external 12 VDC power supply as shown
at right. Plug the power supply into either unit; the powered unit powers the other unit.
Step 7 — Final Installation
a.
Make all connections and test the system for satisfactory operation.
b.
At the power outlet, unplug the power supply.
c.
Mount the transmitter or receiver into the wall box, and attach the supplied decorator-style faceplate to the unit.
d.
At the power outlet, reconnect the power supply. This powers up both units.
Operation
After all devices are powered up, the system is fully operational. See the definitions of the power indications below:
Transmitter and Receiver Power Indicator
1
Power LED — This two-color front panel LED on both transmitter and receiver lights to indicate signal and
power status as follows:
Amber — The unit is receiving power but no signal on the DVI or HDMI input (TP input for receiver).
Green — The unit is receiving power and a signal is present on the DVI or HDMI input (TP input for receiver).
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West
Extron USA - East
+1.714.491.1500
+1.919.850.1000
+1.714.491.1517 FAX
+1.919.850.1001 FAX
Extron Europe
Extron Asia
+800.3987.6673
+800.7339.8766
Inside Europe Only
Inside Asia Only
+31.33.453.4040
+65.6383.4400
+31.33.453.4050 FAX
+65.6383.4664 FAX
©
2017 Extron Electronics All rights reserved.
Extron Japan
Extron China
+4000.EXTRON
+81.3.3511.7655
+4000.398766
+81.3.3511.7656 FAX
Inside China Only
+86.21.3760.1568
+86.21.3760.1566
FAX
www.extron.com
SIG
LINK
DTP OUT
3/16"
(5 mm) Max.
Smooth
Ridges
A
A
SECTION A–A
Power Supply
Output Cord
1
Extron
Extron Korea
Middle East
+82.2.3444.1571
+971.4.2991800
+82.2.3444.1575 FAX
+971.4.2991880 FAX
SIG
LINK
DTP IN
Captive Screw
Connector
DVI-D
DDC
ROUTE
REMOT
Extron India
1800.3070.3777
ON
Inside India Only
AUDIO
1 2
+91-80-3055.3777
+91 80 3055 3737
LOCA
FAX
68-2367-50 Rev. B
05 17
Advertisement
