Front/Rear Panel Features - Numark DM950 Quick Start Owner's Manual

FRONT PANEL FEATURES
3
5
6
8
10
12
1. Power LED: Illuminates when the mixer is
on.
2. Master Gain/Volume: This knob adjusts
the volume of the master output.
3. Channel 1 Control Knobs:
Trim: This knob adjusts the pre-fader
audio level.
Treble: This knob adjusts the high-tone
level.
Bass: This knob adjusts the low-tone
level.
4. Channel 2 Control Knobs:
Trim: This rotary control knob adjusts
the pre-fader audio level.
Treble: This rotary control knob adjusts
the high-tone level.
Bass: This rotary control knob adjusts
the low-tone level.
5. Mic Gain: This rotary control adjusts the
pre-mixer input level.
6. Channel 1 Input Selector: This toggle
selects what input source is routed to the
channel from the rear panel connected units.
7. Channel 2 Input Selector: This toggle
selects what input source is routed to the
channel from the rear panel connected units.
8. Channel 1 Fader: This slide fader is used to
adjust the level sent to program mix.
9. Channel 2 Fader: This slide fader is used to
adjust the level sent to program mix.
10. Replaceable Crossfader: This slide fader
blends audio between the left (channel 1)
and right (channel 2) channels.
Note: This fader is user replaceable if it
should ever wear out. Simply remove the
facepanel and then remove the screws
holding it in position. Replace the fader with
a quality authorized replacement from your
local Numark retailer.
11. Cue Trim & Slider: The Cue Trim rotary
control knob adjusts the volume level of the
headphone output. Channels 1 and 2 can be
previewed using the Cue Slider. Sliding this
to the left plays the left "channel-1" and
sliding to the right plays the right "channel-
2".
2 1
13
12. Microphone Input: Microphones with a ¼"
connector can be connected to this input
terminal.
13. Headphone Jack: Your headphones can be
connected to this ¼" terminal. The volume
should always be set at its lowest setting
while connecting and disconnecting
headphones to prevent damage to
headphones and/or your hearing.
4
REAR PANEL FEATURES
7
9
11
Note: It is recommended that the mixer be
turned off before connecting and
disconnecting any sources to the inputs of the
mixer.
A. Power Switch: Use this switch to turn on
the mixer after all input devices are already
connected to prevent damage to your
equipment. Turn the mixer on before you
turn on amplifiers and turn of amplifiers
before you turn off the mixer.
B. AC Power Input: Microphones with a ¼"
connector can be connected to this input
terminal.
C. Line Inputs: CD players, Tape Decks,
Samplers or other line level input devices
should be connected to these inputs.
D. Phono Inputs: This input is used for
connecting your turntables through the
sensitive RIAA phono preamplifiers. Only
turntables with phono level output should be
attached.
E. GND: This screw connector should be used
to secure any turntables or other devices
connected to the mixer that need to be
grounded.
F. Phono/Line Selector: This switch selects
between the phono and line input on the rear
panel.
G. Master Output (RCA): This output is for
connecting an external monitoring device
such as a PA system, powered monitors or a
home stereo. The level of the master stereo
output signal is controlled by the master
fader.
H. USB Jack: This sends and receives audio
data from your computer. The USB 1 jack
sends audio to the mixer's channel 1, while
the USB 2 jack sends audio to channel 2.
See the separate instructions for how to use
your USB mixer with a computer.