Table of Contents
Advertisement
ONE-KEY™
To learn more about the ONE-KEY™ functionality
for this machine, please refer to the quick reference
included
with
this
https://www.milwaukeetool.com.au/innovation/
one-key/
To download the ONE-KEY™ app, visit the App
Store or Google Play from your smart device.
ONE-KEY™ Indicator
Solid Blue
Wireless mode is active and ready
app.
Blinking Blue
Machine is actively communicating
with the ONE-KEY™ app.
Blinking Red Machine is in security lockout and
can be unlocked by the owner via
the ONE-KEY™ app.
OPERATION
To reduce the risk of injury,
WARNING
always use personal protective
equipment. Always wear eye protection marked
to comply with AS/NZS 1337.1.
Arming the Machine
The MX FUEL™ machines must be armed prior to
use. Even with the battery pack inserted, the machine
functions will not operate until the machine is armed.
To arm the machine:
1. Insert the battery pack.
2. Press the Arm button. The MX FUEL™ icon will
light.
3. After 15 minutes of inactivity, the machine will enter
the LEDs are un-operational.
4. Press and hold the Arm button for 1 second to
reactivate the machine.
5. Press and hold the ARM button for 1 second to
Starting and Stopping
1. Arm the machine.
2. To start the machine, set the switch to the
position.
3. To stop the machine, set the switch to the
position.
Starting and Stopping (Remote Mode)
1. Arm the machine.
2. On the machine, set the switch to the
3. Turn on the remote
4. To start the machine, press the
remote.
5. To stop the machine, press the
remote.
Cold Start LED
The Cold Start LED will illuminate when the
machine is started in cold conditions (below 0°C).
The machine will gradually bring the VPM up to
10,000 in order to avoid nuisance shutdowns. Once
the VPM reaches 10,000 VPM the Cold Start LED
will go off. This feature allows the machine to start in
temps as low as -20°C.
machine
or
go
position.
button on the
button on the
Low Battery Alert
During use, when the battery nears end of charge
(at 10% and 2% remaining charge), the machine
will notify the user by turning itself off and on
to
(pausing). Remove the battery and charge the
battery with a MX FUEL™ battery charger.
General Operation
1. Insert head vertically into material allowing head
to sink to desired depth by its own weight.
2. Hold in place for 5-15 seconds, then slowly lift head
up, staying behind the trapped air's movement to
avoid retrapping air.
3.
A small up and downward movement will close the
hole formed by the head.
4.
To prevent agitating air into material, withdraw the
head quickly when near the top.
5. Move head, re-insert and repeat as desired.
MAINTENANCE
To reduce the risk of injury,
WARNING
always unplug the charger and
remove the battery pack from the charger or
machine before performing any maintenance.
Never disassemble the machine, battery pack
or charger. Contact a MILWAUKEE
facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage
of parts, or any other condition that may affect the
tool operation. Return the tool, battery pack, and
charger to a MILWAUKEE
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work
properly, return the tool, charger and battery pack,
to a MILWAUKEE
Chemical Burn Hazard.
WARNING
This device contains a
lithium button/coin cell battery. A new
or used battery can cause severe in-
ternal burns and lead to death in as
little as 2 hours if swallowed or enters the body.
Always secure the battery cover. If it does not
close securely, stop using the device, remove the
batteries, and keep it away from children. If you
think batteries may have been swallowed or en-
tered the body, seek immediate medical attention.
Internal Battery
An internal battery is used to facilitate full ONE-KEY™
functionality.
To replace the battery:
1. Remove the battery pack.
2. Remove the screw(s) and open the battery door.
3. Remove the old battery, keep it away from children,
and dispose of it properly.
4. Insert the new battery (3V CR2032), with the posi-
tive side facing up.
5. Close the battery door and tighten the screw(s)
securely.
5
service facility for repair.
®
service facility for repairs.
®
ONE-KEY™
service
®
Advertisement
Table of Contents
