Table of Contents
Advertisement
SYMBOLOGY
V
Volts
Direct Current
Vibrations per Minute (VPM)
Read operator's manual
Wear personal protective equipment
(PPE) according to the job site
PPE
requirements.
Wear eye protection
Pairing
Cold Start LED
Remote mode
OFF position
ON position
Regulatory Compliance Mark (RCM).
This
regulatory requirements.
Do not dispose of electric tools
together
material. Electric tools and electronic
equipment that have reached the end
of
their
separately
environmentally compatible recycling
facility.
SPECIFICATIONS
Cat. No. ............................................... MXF CVBC
Battery Type ........................................ MX FUEL™
Charger Type....................................... MX FUEL™
Recommended Ambient
Operating Temperature ....................... 5°C to 40°C
MX FUEL
Li-Ion Battery Packs ............ 72 V DC
TM
Rated VPM ...................................................11,200
Weight (Tool-Only) ........................................ 5.6 kg
Flex Shafts and Heads
MILWAUKEE
®
2.1 m (7') Flex Shaft .......Cat. No. MXF CVS-21M
3.0 m (10') Flex Shaft .....Cat. No. MXF CVS-30M
4.2 m (14') Flex Shaft .....Cat. No. MXF CVS-42M
6.4 m (21') Flex Shaft .....Cat. No. MXF CVS-64M
25 mm (1") Head.......... Cat. No. MXFCVH-25MM
38 mm (1-1/2") Head..Cat. No. MXF CVH-38MM
50 mm (2") Head ........Cat. No. MXF CVH-50MM
64 mm (2-1/2") Head... Cat. No. MXFCVH-64MM
Remote Communication Range .............. Up to 9 m
Battery Type..................................................2xAAA
ONE-KEY
TM
Battery Voltage............................................ 3V DC
Battery Type ............................................. CR2032
product
meets
with
household
life
must
be
and
returned
WARNING
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push the battery latch lock
to the side and squeeze the battery latch lever. Pull
the battery pack away from the machine.
WARNING
To insert the battery, slide the pack into the body of
the machine. Make sure it latches securely into place.
WARNING
Others may be hazardous.
Flex shafts are normally lubricated from the manu-
facturer from one end. Attach the greased end to
for the job.
1. Remove the battery pack.
WARNING
accessories.
2. Open coupler locking handle.
engages. (Handle will automatically fall into place
applicable
with an audible click).
Attaching Head to Flex Shaft
1.
Remove the battery pack.
waste
WARNING
accessories.
collected
2.
to
an
water from entering head
3.
4.
Only use alkaline batteries. Do not use zinc-carbon
batteries. If the remote will not be used for a long
time, remove the batteries as a protection against
corrosion.
To change the batteries:
1. Open the battery compartment.
2. Insert the batteries according to the polarity
marked in the compartment.
3. Close the battery compartment.
1. Arm the machine.
2. On the machine, set the switch to the
3.
Turn on the remote.
4.
On the machine, press and hold the
ready to pair).
5.
Press and hold the
flashing LED on machine will turn solid then
off when the remote has paired successfully.
NOTE: Remote needs to be within close proximity
to ensure remote is receiving signal from the ma-
chine. This procedure will time out in 30 seconds
if machine is not paired.
4
ASSEMBLY
Recharge only with the charger
Always remove battery pack before
changing or removing accessories.
Only use accessorie
recommended for this machine.
Attaching the Flex Shaft
Always remove battery pack
before changing or removing
Always remove battery pack
before changing or removing
Changing Remote Batteries
Pairing the Remote
button on the Remote;
-
position.
button
Advertisement
Table of Contents
