Advertisement
Earbuds
Model | EP-N6 |
Technology | A2DP, AVRCP, HFP, HSP |
Driver (each channel) | 1x 10mm /0.39 '' speaker driver |
Sensitivity | 103±3dB |
Frequency Range | 20Hz – 20kHz |
Impedance | 16ohm ± 15% |
Microphone Type | MEMS (microphone chip) |
Microphone Sensitivity | -7dB±4dB (at 1kHz) 1Pa |
Microphone Frequency Range | 100Hz~10KHz |
Charging Time | 2 hours |
Battery Life | Up to 5 hours |
Battery Type | Li-polymer(2×50mAh) |
Operating Range | 15m / 50ft |
IP Rating | IPX5 |
Weight | 9g(pair)/ 0.31oz |
Charging Case
Charging Input | DC 5V |
Charging Time | 2 hours |
Battery Type | Li-polymer (380mAh) |
Number of Earbuds Recharges | 4 times (pair) |
Weight | 28g / 0.99oz |
Note: Remove the protective film from the earbuds before first time usage
Turn On | Open the lid of the charging case, or press and hold the touch-sensitive panels on both earbuds for 2 seconds whilst they are turned off |
Turn Off | Return both earbuds to the charging case or touch and hold on the touch-sensitive panels on both earbuds for 10 seconds when they are turned on |
Begin with the earbuds in their case:
Once the earbuds have been successfully paired to your device, they can be switched on and off as follows:
Starting with the earbuds in the case:
Once paired, you can wirelessly stream audio from your device to the earbuds. Music will automatically pause when you receive an incoming phone call and resume once the call has ended.
Play or pause | Double-Tap the touch-sensitive panel on either earbud |
Skip to next track | Triple-tap the touch-sensitive panel on the right earbud |
Skip to previous track | Triple-tap the touch-sensitive panel on the left earbud |
Answer or end a call | Double-tap the touch-sensitive panel on either earbud to answer or end a call | |
Reject an incoming call | Touch and hold the touch-sensitive panel on either earbud for 2 seconds | |
Use Siri or other voice assistants | While your device is connected, quadruple-tap the touch-sensitive panel on either earbud |
LED Status Indicator (Earbuds) | Status | |
Green | Earbuds are fully charged | |
Red | Earbuds are charging | |
LED Charging Indicator (Charging case) | Battery Status | |
Flashing Green | > 90% | |
Flashing Red and Green | > 50% | |
Flashing Red | < 50% |
For questions, support, or warranty claims, contact us at the address below that corresponds with your region. Please include your Amazon order number and product model number.
Amazon US orders: support.us@aukey.com
Amazon EU orders: support.eu@aukey.com
Amazon CA orders: support.ca@aukey.com
*Please note, AUKEY can only provide after sales service for products purchased directly from AUKEY. If you have purchased from a different seller, please contact them directly for service or warranty issues.
Max RF power level:
BT classic (2402–2480MHz): 2.1dBm
RF exposure assessment has been performed to prove that this unit will not generate the harmful EM emission above the reference level as specified in EC Council Recommendation (1999/519/EC).
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
NOTE: Excessive sound pressure from earphones and headphones can cause hearing loss if used for extended periods.
Hereby, Aukey Technology Co., Ltd. declares that the radio equipment type (True Wireless Earbuds, EP-N6) complies with Directive 2014/53/EU.
Notice: This device may be used in each member state of the EU.
Aukey Technology Co., Ltd.
www.aukey.com
support@aukey.com
Room 102, Building P09, South China City Electronics
Trading Center, Longgang District, Shenzhen,
Guangdong, 518111, China
FCC ID: 2ATIH-EP-N6L
FCC ID: 2ATIH-EP-N6R
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the EP-N6 and is the answer not in the manual?
Questions and answers