Advertisement
Earbuds
Model | EP-T25 |
Technology | BT 5, A2DP, AVRCP, HFP, HSP, AAC |
Driver (each channel) | 1 x 6mm / 0.24" speaker driver |
Sensitivity | 90 ±3dB SPL (at 1kHz/1mW) |
Frequency Range | 20Hz – 20kHz |
Impedance | 16 ohm ±15% |
Microphone Type | MEMS (microphone chip) |
Microphone Sensitivity | -38dB ±1dB (at 1kHz) |
Microphone Frequency Range | 100Hz – 10kHz |
Charging Time | 1 hour |
Battery Life | Up to 5 hours |
Battery Type | Li-polymer (2 x 40mAh) |
Operating Range | 10m / 33ft |
IP Rating | IPX5 |
Weight | 7g / 0.25oz (pair) |
Charging Case
Charging Input | DC 5V |
Charging Time | 1.5 hours |
Battery Type | Li-polymer (350mAh) |
Number of Earbuds Recharges | 4 times (pair) |
Weight | 28g / 0.99oz |
Fully charge the charging case before first use. To charge, connect the case to a USB charger or charging port with the included USB-A to C cable. When all 4 LED charging indicator lights are blue, the case is fully charged. Charging takes around 1.5 hours, and after being fully charged, the case can fully charge the earbuds 4 times. The earbuds should be stored in the case when not in use. When the earbuds are charging in the case (with the case itself not charging) and the case is opened, the LED charging indicator is solid red. When the red indicator turns blue, the earbuds are fully charged.
Turn On | Open the lid of the charging case or touch and hold the touch-sensitive panels on both earbuds for 4 seconds when they are turned off |
Turn Off | Close the lid of the charging case or touch and hold the touch-sensitive panels on both earbuds for 6 seconds when they are turned on |
Starting with the earbuds in the case:
Once the earbuds are successfully paired with your device, they can be switched on and off as follows:
Starting with the earbuds in the case:
Notes
Once paired, you can wirelessly stream audio from your device to the earbuds. Music will automatically pause when you receive an incoming phone call and resume once the call has ended.
Play or pause | Tap the touch-sensitive panel on either earbud |
Skip to next track | Double-tap the touch-sensitive panel on right earbud |
Skip to previous track | Double-tap the touch-sensitive panel on left earbud |
Answer or end a call | Double-tap the touch-sensitive panel on either earbud to answer or end a call. If there's a second incoming call, double-tap the touch-sensitive panel on either earbud to answer the second call and end the first call; or touch and hold the touch-sensitive panel on either earbud for 2 seconds to answer the second call and put the first call on hold |
Reject an incoming call | Touch and hold the touch-sensitive panel on either earbud for 2 seconds |
Use Siri or other voice assistants | While your device is connected, triple-tap the touch-sensitive panel on either earbud |
LED Charging Indicator | Status |
Red | Earbuds charging |
Blue | Earbuds fully charged |
LED Battery Level Indicator | Status |
Flashing blue | Case charging |
Solid blue | Case fully charged |
For the earbuds and your device to establish a connection, you need to put them both in pairing mode. Please follow the instructions in the Pairing section of this manual.
Double-check the volume level on your smartphone and the earbuds. Some smartphones require you to set up the earbuds as an audio output device before the audio can be transmitted. If you're using a music player or other device, please make sure it supports the A2DP profile.
Adjust the volume on your smartphone and the earbuds. Try moving closer to your smartphone to rule out the possibility of interference or wireless range-related issues.
The maximum range is 10m (33ft). However, the actual range depends on environmental factors. For optimal performance, keep your device connected within a range of roughly 4m to 8m and make sure that there are no major obstacles (like reinforced steel walls) between the earbuds and your device.
Try charging the earbuds for a while. If the earbuds still won't power on, please contact our support team at the email address given in Warranty & Customer Support.
The charging case is probably out of power. Try charging it.
For questions, support, or warranty claims, contact us at the address below that corresponds with your region. Please include your Amazon order number and product model number.
Amazon US orders: support.us@aukey.com
Amazon EU orders: support.eu@aukey.com
Amazon CA orders: support.ca@aukey.com
Amazon JP orders: support.jp@aukey.com
*Please note, AUKEY can only provide after sales service for products purchased directly from AUKEY. If you have purchased from a different seller, please contact them directly for service or warranty issues.
Max RF power level:
BT classic (2402–2480MHz): 2.1dBm
RF exposure assessment has been performed to prove that this unit will not generate the harmful EM emission above the reference level as specified in EC Council Recommendation (1999/519/EC).
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Excessive sound pressure from earphones and headphones can cause hearing loss.
Hereby, Aukey Technology Co., Ltd. declares that the radio equipment type (True Wireless Earbuds, EP-T25) is in compliance with Directive 2014/53/EU.
Notice: This device may be used in each member state of the EU.
Aukey Technology Co., Ltd.
www.aukey.com | support@aukey.com
Building P09, South China City Electronics Trading Center,
Longgang District, Shenzhen, Guangdong, 518111, China
IC ID: 24100-EPT25 FCC ID: 2ATIH-EPT25
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the EP-T25 and is the answer not in the manual?
Questions and answers