Related Manuals for Marvel MLCP215 -SS81A
Summary of Contents for Marvel MLCP215 -SS81A
- Page 1 GE T TING STARTED QUICK REFERENCE GUIDE MARVEL U NDER COU NTER R EF R IG ER ATION M L C P 2 1 5 - S S 8 1 A M L C P 2 1 5 - I S 8 1 A...
-
Page 2: Table Of Contents
Got a Marvelous Design? NOTE- Important information to help assure a problem We would love to see how your Marvel product looks in its free installation and operation. new home. Send us photos at marketing@marvelrefriger- ation.com, and we might feature your Marvel home design... -
Page 3: Unpacking Your Appliance
UNPACKING YOUR APPLIANCE CAUTION WARNING If the appliance was shipped, handled or stored in other EXCESSIVE WEIGHT HAZARD than an upright position for any period of time, allow the ap- Use two or more people to move product. pliance to sit upright for a period of at least 24 hours before Failure to do so can result in personal injury. -
Page 4: Electrical
ELECTRICAL Electrical Connection A grounded 115 volt, 15 amp dedicated circuit is required. This product is factory equipped with a power supply cord that has a three-pronged, grounded plug. It must be plugged into a mating grounding type receptacle in accor- dance with the National Electrical Code and applicable Do not remove local codes and ordinances. -
Page 5: Installing Your Appliance
- even if they sit out for "just a few hours". ice production. For this reason it is important this area not be obstructed and the grille openings kept clean. Marvel follow the instructions below to help prevent does not recommend the use of a custom made grille as accidents. - Page 6 INSTALLING YOUR APPLIANCE Minimum Maximum WARNING Model Height Height " Electrical Shock Hazard " MLC**15 • Do not use an extension cord with this appliance. MOC**15 They can be hazardous and can degrade product Table A MP**15 performance. • electrical supply. •...
-
Page 7: Door Reversal
DOOR REVERSAL Door Reversing Instructions Tools Needed: • 1/8” Hex Key • 5/32” Hex Key • Phillips Screwdriver Open door and remove Hinge Pin from the Upper Hinge using a 1/8” Hex Key tool making sure to steady the Using a Phillips Screwdriver, remove the 6 screws from both the Upper and Lower Hinges and save for later steps Once the Hinges are removed from the unit, using a Phillips Screwdriver, remove the Bushing Screw and Hinge Pin Screw and save for later steps On the Bottom Hinge, reattach the Bushing Screw and Hinge Pin Screw to the opposite side... - Page 8 DOOR REVERSAL 6. Remove the door switch actuator tab from the door and attach it to the opposite side Door switch actuator tab 7. Reattach the Upper and Lower Hinges, and Hinge Brackets to opposite sides. Then install the door.
-
Page 9: Using Your Electronic Control
USING YOUR ELECTRONIC CONTROLS Control Function Guide Function Command Notes ON/OFF Press and release. Unit will immediately turn ON or OFF. Option Open Door Closed Door White White Hold and press and release . Press Adjust light color to scroll through lighting options. BrightShield BrightShield White... - Page 10 USING YOUR ELECTRONIC CONTROLS BrightShield™...
-
Page 11: Installing The Water Supply
INSTALLING THE WATER SUPPLY Water Supply CAUTION Observe and follow all local building codes when installing this appliance. This ice machine must be connected to a potable cold water supply line. delivering water pressure between a minimum of 20 psi and a maximum of 120 psi. "... -
Page 12: Ice Maker Operation
ICE MAKER OPERATION The Ice Making Process sheet is released and slides onto the grid cutter cutter’s heated fractional freezing to form a slab of ice that is clear and wires. The water containing the dissolved minerals is has less dissolved solids than the water it is produced drained after each freezing cycle. - Page 13 ICE MAKER OPERATION Ice Production The ice machine will keep producing ice until the ice machine’s bin is full and will restart automatically when In normal mode the ice machine will produce up to 39 ice needs to be replenished in the bin. The ice bin is pounds (17.7 kg) of clear ice in a 24-hour period when installed in a 72°F ambient with a 55°F water supply.
- Page 14 "nickel safe" ice maker cleaner. You can order ice machine plate and grid cutter cleaner (part # S41013789) at marvelrefrigeration.com. area that is not embedded in wires CAUTION Use only Marvel-approved ice machine cleaner and follow all label warnings and directions. Incorrect chemical warranty.
-
Page 15: Care And Cleaning
CARE AND CLEANING Remove ice from bin. Pull plug from the reservoir. Once reservoir is empty, replace plug. Hold the button for 10 seconds to show "CL" on the display. Lift Fascia door to access evaporator plate. Lift or remove splash shield to expose evaporator plate. - Page 16 CARE AND CLEANING Front Grille Be sure that nothing obstructs the required air flow openings i n front of the cabinet. At least once or twice a year, brush or vacuum lint and dirt from the front grille area. CAUTION Disconnect electrical power from the SHOCK HAZARD: appliance before cleaning with soap and water.
-
Page 17: Warranty
For designated Marvel Professional product, Marvel offers a one year extension of the two year warranty coverage from the date of purchase, free of charge. To take advantage of this third year warranty, you must register your product with Marvel within 60 days from the date of purchase at marvelrefrigeration.com and provide proof of purchase. - Page 18 Marvel Refrigeration 1260 E. Van Deinse St. Greenville MI 48838 616.754.5601 30701 Rev A 1/10/23 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for...
Need help?
Do you have a question about the MLCP215 -SS81A and is the answer not in the manual?
Questions and answers