Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Bradley Manuals
  4. Toilets
  5. Bradmar 700 Series
  6. Installation manual

Bradley 700 Series Installation Manual

Hide thumbs Also See for 700 Series:

Advertisement

Quick Links

Download this manual
For Standard Height
Doors and Panels Only
Before beginning installation, make sure that the wall and floor backing are adequate to support the secure
mounting of the toilet compartment units.
To prevent warping, always lay the material flat. Do not lean the material against the wall or stack unevenly.
To prevent "dimpling," extra caution should be taken when instructed to drill through one side of face only.
Read this installation manual completely to ensure proper installation, then file it with the owner or
maintenance department. This installation manual provides instruction for the assembly of normal partition
configurations and standard components. Non-standard configurations or components including but not
limited to curved or angled walls, partial walls, oversized panels, or modified hardware are not covered in
this manual. Compliance and conformity to local codes and ordinances is the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for before discarding packaging
material. If any parts are missing, do not begin installation until you obtain the missing parts.
Product warranties and parts information may be found on Bradley's web site at bradleycorp.com.
*HDWT-INSTR-012*
HDWT-INSTR-012 Rev. G: ECO 22-14-006
© 2023 Bradley
Page 1 of 27
1/23/2023
Installation
Powder Coated & Stainless Steel
Restroom Partitions
Floor-to-Ceiling - Series 700

Table of Contents

Pre-Installation Information . . . . . . . . . . . . . . . . . . . . 2
Layout Dimensions for Brackets . . . . . . . . . . . . . . . . 3
Mounting Brackets to Wall . . . . . . . . . . . . . . . . . . . 4-5
Leveling Bolts to Pilaster . . . . . . . . . . . . . . . . . . . . . . 5
Mounting Brackets to Pilasters . . . . . . . . . . . . . . . 6-7
Pilaster Mounting Hardware . . . . . . . . . . . . . . . . . 7-8
Pilasters and Panels . . . . . . . . . . . . . . . . . . . . . . 9-11
Telescoping and Wall Hung Pilasters . . . . . . . . 12-15
Pilaster Shoes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-20
Door Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . 21-24
Urinal Screens . . . . . . . . . . . . . . . . . . . . . . . . . . 25-27
WARNING
NOTICE
IMPORTANT
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
+1 262 251 6000
bradleycorp.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the 700 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Bradley 700 Series

Summary of Contents for Bradley 700 Series

  • Page 1: Table Of Contents

    Separate parts from packaging and make sure all parts are accounted for before discarding packaging material. If any parts are missing, do not begin installation until you obtain the missing parts. Product warranties and parts information may be found on Bradley's web site at bradleycorp.com. *HDWT-INSTR-012* P.O.
  • Page 2 60-1/2" 36" (1537mm) (914mm) wall to center to centerline center 1" (25mm) 61-1/4" (1556mm) to face 1/2" 20-1/2" (13mm) 3" (76mm) 36" 24" 26" 8" (914mm) (610mm) (660mm) (203mm) 1" (25mm) gap Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 3 "A1" ("B") . Repeat this step for each panel, starting each measurement from the last panel centerline ("B1") . Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 4 [51mm] deep) at each hole location . Insert the plastic anchors in all holes and secure the brackets to the wall with the "Ear" "U" Bracket #14 x 2" stainless screws provided . Bracket Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...

  • Page 5: Leveling Bolts To Pilaster

    4" - 8" pilasters have a single, 1-piece bracket that uses a Use leveling bolt(s) to adjust height of pilaster leveling bolt in the center to adjust the pilaster height. as indicated based on pilaster width . Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 6 Ø3/16" pilot hole (through inside face of pilaster only) at each location . "B" Secure the continuous bracket to the pilasters using the #14 x 5/8" stainless screws provided . Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 7 . Insert plastic anchors into the holes and fasten the "L" brackets to the anchors using the #14 x 2" screws provided . Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...

  • Page 8: Pilaster Mounting Hardware

    Insert the plastic anchor and secure the bracket to the ceiling with the #14 x 2" (13mm) in from each outer edge line and flush stainless screw provided . with the projected inside face line . 1/2" (13mm) Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 9 . Secure the pilaster to the bracket using the Secure the panel to the bracket using the #14 x 5/8" #14 x 5/8" screws provided . screws provided . Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...

  • Page 10: Pilasters And Panels

    . Secure the pilaster to the bracket using the Secure the panel to the bracket using the #14 x 5/8" #14 x 5/8" stainless screws provided . stainless screws provided . Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 11 #10-24 x 3/4" stainless #10-24 x 3/4" stainless barrel nuts and #10-24 x 1" barrel nuts and #10-24 x 3/4" stainless shoulder screws stainless shoulder screws provided . provided . Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 12 Pilaster Mounting Channel Centerline Telescoping Telescoping Pilaster at Wall Channel Mounting Channel Specified Dimension Mounting Channel Pilaster Plumb Line 12-1/8" (308mm) to Bottom of Channel (Highest Point in Floor) Floor 12-1/8" (308mm) Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 13 . Secure the pilaster to the bracket using the #14 x 5/8" screws provided . #14 x 5/8" screws provided . Wall Specified Dimension (Standard Gap 1") Specified Dimension Pilaster Plumb Line 12" (305mm) Floor Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 14 . Secure the pilaster to the bracket using the #14 x 5/8" stainless screws provided . #14 x 5/8" stainless screws provided . Wall Specified Dimension (Standard Gap 1") Specified Dimension Pilaster Plumb Line 12" (305mm) Floor Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 15 #10-24 x 3/4" stainless barrel nuts and #10-24 x 1" stainless shoulder screws provided . stainless shoulder screws provided . Wall Specified Dimension (Standard Gap 1") Specified Dimension Pilaster Plumb Line 12" (305mm) Floor Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...

  • Page 16: Pilaster Shoes

    Continuous Hinge: Position the top shoe so that it rests flush with the ceiling . Position bottom shoe so that it rests flush with the floor . Repeat Step C to secure shoe to pilaster . Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 17 56-3/16" result in the top of the door being flush with the top of the pilaster when the desired cam 58" (52mm) (1427mm) setting on the door is set to 0°. (1473mm) Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...

  • Page 18: Hinges

    "at rest" position . For doors requiring a full close, rotate the door 15° past the closed position. Finished View of Top Hinge Bottom Hinge Finished View of Bottom Hinge Lock Nut Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 19 #10-24 x 3/4" stainless barrel nuts and #10-24 x 1" stainless shoulder screws provided . Drill Ø1/4" holes through the remaining hinge holes on the door and pilaster . Secure with the fasteners provided . Spacer 12" (305mm) Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 20 #10 x 2" stainless flat head screws provided . 68-3/8" (1737mm) See Step 8, E thru G for instructions on attaching the door to the hinge . Floor 12" (305mm) Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 21 Using the flat strike/keeper as a template drill (2) Ø1/8" pilot holes through one face of the pilaster only . Secure the flat strike/keeper with the #10 x 3/4" flat head screws provided . Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...

  • Page 22: Door Hardware

    Using the flat strike/keeper as a template, drill (2) Ø1/8" pilot holes through one face of the pilaster only . Secure the flat strike/keeper with the #10 x 3/4" flat head screws provided . Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 23 #10 x 3/4" flat head secure with the #14 x 5/8" screws provided . screws provided . Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 24 (914mm) keeper to the pilaster using face of the pilaster only and the #10 x 3/4" flat head secure with the #14 x 5/8" screws provided . screws provided . Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 25 Using the bracket as a template, drill Ø3/16" holes through the urinal screen at each bracket hole . Secure the urinal screen to the brackets with the #14 x 5/8" screws provided . Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...

  • Page 26: Urinal Screens

    Using the bracket as a template, drill Ø3/16" holes through the urinal screen at each bracket hole . Secure the urinal screen to the bracket with the #14 x 5/8" stainless screws provided . Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...
  • Page 27 Using the bracket as a template, drill Ø1/4" holes through the urinal screen at each bracket hole . Secure the urinal screen to the bracket with the #10-24 x 3/4" stainless barrel nuts and #10-24 x 3/4" stainless shoulder screws provided . Bradley • HDWT-INSTR-012 Rev. G: ECO 22-14-006 1/23/2023...