Table of Contents
Advertisement
Quick Links
Camera
1/4-20 x 3/8 Screw
Dome Plugs
Terminal Lug
Screw
I
Fuseholder
N S T A L L A T I O N A N D
Loosen These Screws
Do Not Remove
Camera
Bracket
6.4 mm
0.25 in
Rear Cap
1/2-inch
Rubber Plugs
Foot
3/8-inch NPT
Fitting
Ground
Neutral
Line
W W W
D
ESIGNER
O
P E R A T I N G
.
A I G I S M E C H
S
H
ERIES
OUSINGS
HS948
X
I
N S T R U C T I O N S
.
C O M
S
ERIES
Advertisement
Table of Contents
Related Manuals for Aigis Mechtronics HS948 Series
Summary of Contents for Aigis Mechtronics HS948 Series
- Page 1 Loosen These Screws ESIGNER ERIES OUSINGS Do Not Remove Camera Camera Bracket 6.4 mm 1/4-20 x 3/8 Screw 0.25 in Rear Cap Remove These Dome Plugs 1/2-inch Rubber Plugs HS948 Foot ERIES 3/8-inch NPT Fitting Ground Terminal Lug Neutral Screw Line Fuseholder N S T A L L A T I O N A N D...
-
Page 2: Important Safeguards
IMPORTANT SAFEGUARDS 12. Power Lines - An outdoor system should not be located in the vicinity of overhead power lines or other electric light 1. Read Instructions - All the safety and operating or power circuits or where it can fall into such power lines instructions should be read before the unit is operated. -
Page 3: Safety Precautions
SAFETY PRECAUTIONS SICHERHEITSVORKEHRUNGEN VORSICHT: UM EINEN ELEKTRISCHEN SCHLAG ZU CAUTION: TO REDUCE THE RISK OF ELECTRICAL VERMEIDEN, ABDECKUNG NICHT ENTFERNEN. SHOCK, DO NOT OPEN COVERS. NO USER SERVICE- WARTUNGEN ALLER ART QUALIFIZIERTEM PERSON- ABLE PARTS ARE INSIDE. REFER SERVICING TO QUALI- AL ÜBERLASSEN. -
Page 4: Installation
If any items HS9483-6H Heater 115/23 HS9483-6HB Heater/Blower 115/28 are missing, notify Aigis Mechtronics. HS9484-2H Heater 24/23 The shipping carton is the safest container in which the unit HS9484-2HB Heater/Blower 24/25 may be transported. -
Page 5: Maximum Camera/Lens Size
(6.1 Model Designation Continued) 6.4 Cable Requirements Model Preinstalled Voltage/ Use with Camera Video Transmission (Coaxial) Components Power Models with These Cable Type: RG-59/U for runs < 300 m (1000 ft). Voltage Ratings RG-11/U for runs < 600 m (2000 ft). Outdoor Units (cont.) Cable Size: Outside diameter between... -
Page 6: Housing Mounting
6.5 Housing Mounting 6.7 Camera/Lens Installation Use the two 1/4-20 x 1/2-inch screws and a 1/4-inch Loosen the two screws holding the camera bracket to spring washers provided in the hardware kit to mount the base. It is not necessary to remove them completely. the housing to a mount or a pan/tilt. -
Page 7: Camera/Lens Wiring
e. Tighten the fitting to 4.0 N. 35 in lb to 40 in lb). This 6.7.2 For installation of zoom lens cameras mounted torque rating is approximately 1 to 1-1/2 turns past the in HS9484 Series & HS9488 Series Housings: point where the fitting starts to grip the wire. - Page 8 6.8.3 Conduit 6.8.5 Power Connections These housings are designed to allow conduit to be directly Power connection into the housings is to be supplied through connected. a minimum type UL Standard "SJ" cord acceptable for outdoor use. Installation must conform to acceptable NEC Remove the rear fittings and attach the conduit and and local codes.
-
Page 9: Video Coax Connection
Attach BNC connector to the coax and connect it to the camera. Pull any excess wire out of the housing and tighten the fitting to 8.5 N . m to 9.0 N . m (75 in . lb to 80 in . -
Page 10: Camera/Lens Adjustment
Dimensional Outlines 6.11 Camera/Lens Adjustment Verify camera and lens operation before final assembly of the cradle into the housing. Adjust the camera focus and iris as HS9480 necessary. See individual camera instructions. 10.9 6.12 Final Assembly Use the plugs or fittings provided to plug any remaining holes in the rear cap. - Page 11 HS9484-IP & HS9484-2HBIP) THESE DRAWINGS AND SPECIFICATIONS ARE T THESE DRAWINGS AND SPECIFICATIONS ARE T AIGIS MECHTRONICS INC, AND ARE NOT TO BE AIGIS MECHTRONICS INC, AND ARE NOT TO BE MANUFACTURE OR SALE OF APPARATUS AND MANUFACTURE OR SALE OF APPARATUS AND...
- Page 12 Front Cap Screw, Washer, Bushing Housing Secure with screw as shown. ©2008 Aigis Mechtronics 1124 Louise Road, Winston-Salem, NC 27107-5450 Tel: 336.785.7740 Fax: 336.785.7744 100 0061 003 AIG 03/08 WWW.AIGISMECH.COM Printed in U.S.A. Data subject to change without notice...
Need help?
Do you have a question about the HS948 Series and is the answer not in the manual?
Questions and answers