Related Manuals for Aigis Mechtronics HS9383S-2HP
Summary of Contents for Aigis Mechtronics HS9383S-2HP
- Page 1 Stainless Steel Pressurized Housing HS9383S-2HP HS9383S-P N S T A L L A T I O N A N D P E R A T I N G N S T R U C T I O N S W W W...
- Page 2 IMPORTANT SAFEGUARDS Read Instructions - All the safety and operating 12. Power Lines - An outdoor system should not be located instructions should be read before the unit is operated. in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such Retain Instructions - The safety and operating instructions power lines or circuits.
-
Page 3: Fcc & Ices Information
FCC & ICES INFORMATION (U.S.A. and Canadian Models Only) WARNING - This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and ICES-003 of Industry Canada. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. -
Page 4: Care And Maintenance
1/4 Lock Washer Bit Driver 5/32 SERVICE If the unit ever needs repair service, the customer should contact Aigis Mechtronics for return authorization and shipping instructions. CARE AND MAINTENANCE There are no moving parts in this unit. Regularly scheduled maintenance will help prolong the operation life of this unit. -
Page 5: Installation
CAUTION This installation should be made by qualified service personnel and conform to all local codes. Model Designation Model Rated Input Range HS9383S-2HP* 24VAC 21.6 to 26.6 50/60 Hz HS9383S-P *Power Requirements: Heater requires 10 watts. Do Not Exceed 30 VAC Input on 24 VAC models. Operation above 30 VAC violates low voltage operation (Class 2 Specifications). - Page 6 Camera/Lens Installation With the cradle removed from the housing, follow all of the steps below for the lens type to be installed. Place the camera/lens combination into the cradle assembly. Fixed Lens Cameras: Position the camera/lens 1 mm (0.04 in) away from the faceplate. The camera/lens are secured to the cradle with 1/4-20 button head cap screw (BHCS), with a combination of nylon spacers and washers to align the lens in the center of the viewing window.
- Page 7 Making the Wire Harness Zoom Lens Models Zoom 1. Feed the power and video wires through the back of the connection coupler. Focus 2. Slide on the white seal sleeve onto the wires. Common 3. Strip the wire using the manufacture’s specs to crimp and pin out the wires into the wire harness plug. See the wiring diagram below.
- Page 8 Connecting the Wire Harness to the Housing 1. After completing the wiring harness, make sure the O-Ring is in place at the bottom of the threads on the rear cap of the housing. 2. Insert the wire harness plug into the back of the housing. O-Ring 3.
- Page 9 4. In a chris-cross pattern using the 5/32-inch hex wrench, tighten down the three BHC SS screws in the back of the coupler. Tighten all three screws...
- Page 10 5.8 Pressurization 1. The housing is fitted with a standard Schrader valve to allow pressurization with dry nitrogen to 35 kPa (5 lb PSIG) nominal at one atmosphere. Using the Schrader Valve add 10psi nitrogen to pressurize the housing. 2. An overpressurization safety relief valve is mounted on the rear cap along with the Schrader valve. The purpose of the relief valve is to provide a safety pressure blow-off should internal pressure exceed 140 kPa (20 PSIG) at one atmosphere.
-
Page 11: Dimensional Outlines
DIMENSIONAL OUTLINES 304,8 12.0 350,2 13.79 ø 88,9 3.50 203,2 ø 8.00 ø 95,3 3.75 71,9 5.832 302,6 11.91 355,6 14.00... - Page 12 100 0193 001 AIG 02/07 ©2005 Aigis Mechtronics Draft Printed in U.S.A. 1124 Louise Road Winston-Salem, NC 27107-5450 Tel: 336.785.7740 Fax: 336.785.7744 Data subject to change without notice.
Need help?
Do you have a question about the HS9383S-2HP and is the answer not in the manual?
Questions and answers