Endress+Hauser HART Levelflex FMP55 Operating Instructions Manual
Guided wave radar
Hide thumbs
Also See for HART Levelflex FMP55:
- Operating instructions manual (214 pages) ,
- Technical information (100 pages) ,
- Brief operating instructions (64 pages)
Related Manuals for Endress+Hauser HART Levelflex FMP55
Summary of Contents for Endress+Hauser HART Levelflex FMP55
- Page 1 Products Solutions Services BA01003F/00/EN/21.20 71488044 2020-07-31 01.03.zz (Device firmware) Operating Instructions Levelflex FMP55 HART Guided wave radar...
- Page 2 Levelflex FMP55 HART Order code: XXXXX-XXXXXX Ser. no.: XXXXXXXXXXXX Ext. ord. cd.: XXX.XXXX.XX Serial number www.endress.com/deviceviewer Endress+Hauser Operations App A0023555 Endress+Hauser...
-
Page 3: Table Of Contents
Mounting cladded flanges ..21 (DD) ....... 65 Endress+Hauser... - Page 4 15.1 General notes ......15.1.1 Repair concept ....Endress+Hauser...
-
Page 5: Important Document Information
Direct current and alternating current Direct current Ground connection A grounded terminal which, as far as the operator is concerned, is grounded via a grounding system. Protective earth (PE) Ground terminals that must be connected to ground prior to establishing any other connections. Endress+Hauser... -
Page 6: Tool Symbols
1, 2, 3, ... Item numbers A, B, C, ... Views Safety instructions Observe the safety instructions contained in the associated Operating Instructions Temperature resistance of the connection cables Specifies the minimum value of the temperature resistance of the connection cables Endress+Hauser... -
Page 7: Documentation
For an overview of the scope of the associated Technical Documentation, refer to the following: • W@M Device Viewer (www.endress.com/deviceviewer): Enter the serial number from nameplate • Endress+Hauser Operations App: Enter the serial number from the nameplate or scan the 2D matrix code (QR code) on the nameplate 1.3.1 Technical Information (TI) -
Page 8: Registered Trademarks
Registered trademark of the FieldComm Group, Austin, Texas, USA Bluetooth® The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Endress+Hauser is under license. Other trademarks and trade names are those of their respective owners. Apple®... -
Page 9: Basic Safety Instructions
The manufacturer is not liable for damage caused by improper or non-designated use. Clarification of borderline cases: ‣ For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in verifying the corrosion resistance of fluid-wetted materials, but does not accept any warranty or liability. -
Page 10: Occupational Safety
The measuring system meets the legal requirements of the applicable EU Directives. These are listed in the corresponding EU Declaration of Conformity along with the standards applied. Endress+Hauser confirms successful testing of the device by affixing to it the CE mark. 2.5.2 EAC conformity The measuring system meets the legal requirements of the applicable EAC guidelines. -
Page 11: Product Description
Levelflex FMP55 HART Product description Product description Product design 3.1.1 Levelflex FMP51/FMP52/FMP54/FMP55 A0012399 1 Design of the Levelflex Electronics housing Process connection (here as an example: flange) Rope probe End-of-probe weight Rod probe Coax probe Endress+Hauser... -
Page 12: Electronics Housing
Electronics housing A0012422 2 Design of the electronics housing Electronics compartment cover Display module Main electronics module Cable glands (1 or 2, depending on instrument version) Nameplate I/O electronics module Terminals (pluggable spring terminals) Connection compartment cover Grounding terminal Endress+Hauser... -
Page 13: Incoming Acceptance And Product
• Enter the serial number from the nameplates into the Endress+Hauser Operations App or scan the 2-D matrix code (QR code) on the nameplate with the Endress+Hauser Operations App: all the information for the measuring device is displayed. Endress+Hauser... -
Page 14: Nameplate
Only 33 digits of the extended order code can be indicated on the nameplate. If the extended order code exceeds 33 digits, the rest will not be shown. However, the complete extended order code can be viewed in the operating menu of the device in the Extended order code 1 to 3 parameter. Endress+Hauser... -
Page 15: Storage, Transport
Pay attention to the center of gravity of the device so that it does not tilt or slip unintentionally. ‣ Follow the safety instructions and transport conditions for devices weighing more than 18 kg (39.6 lbs) (IEC 61010). Endress+Hauser... - Page 16 These cable ties must not be released during transportation or installation of the device to prevent the spacer from sliding at the probe rod. They may only be removed immediately before screwing the process connection flange into place. Endress+Hauser...
- Page 17 Levelflex FMP55 HART Storage, transport A0015471 Endress+Hauser...
-
Page 18: Installation
• Coax probes can be mounted at any distance from the wall. • When mounting outdoors, a weather protection cover can be used to protect the device against extreme weather conditions. • Minimum distance from the end of the probe to the bottom of the vessel: 10 mm (0.4 in) Endress+Hauser... -
Page 19: Mounting Under Confined Conditions
The probe, electronics and connection cable are mutually compatible and bear a common serial number. Only components with the same serial number may be connected to one another. Endress+Hauser... -
Page 20: Notes On The Mechanical Load Of The Probe
Tensile loading capacity of rope probes FMP55 Rope 4mm (1/6") PFA>316 2 kN Lateral loading capacity (flexural strength) of rod probes FMP55 Rod 16mm (0.63") PFA>316L 30 Nm 6.1.4 Lateral loading capacity (flexural strength) of coax probes FMP55 Probe Ø 42.4 mm316L 300 Nm Endress+Hauser...
Need help?
Do you have a question about the HART Levelflex FMP55 and is the answer not in the manual?
Questions and answers