Table of Contents
Advertisement
Quick Links
Gared Outer Limit Pro Portable Backstop
Installation, Operation and Maintenance Instructions
Please read all instructions before attempting installation or operation of these units
SAVE THESE INSTRUCTIONS FOR FUTURE USE
P
N
.
UBLICATION
O
551756323
Models: 9716S, 9718S, 9716E & 9618E
Revised
July 12, 2022
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Gared PSS 9716S
Summary of Contents for Gared PSS 9716S
- Page 1 Gared Outer Limit Pro Portable Backstop Models: 9716S, 9718S, 9716E & 9618E Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE Revised UBLICATION 551756323 July 12, 2022...
-
Page 2: Table Of Contents
Troubleshooting ......................23 Introduction Thank you for your purchase of a Gared Sports model Outer Limit Pro Portable backstop. To ensure that our equipment will provide years of use to you, we are including this installation, operation, and maintenance guide. This guide will provide information on the proper assembly and installation methods, operating procedures, and preventative maintenance of your portable backstop. -
Page 3: Basic Dimensions
Gared Outer Limit Pro Portable Backstop BASIC DIMENTIONS 9716S, 9716E (8’-0” F.O.B.) Play Weight MODEL lbs [Kg] 9716S w/ std ballast 2990 [1356 Kg] w/ opt ballast 3460 [1569 Kg] 9716E w/ std ballast 3022 [1371 Kg] w/ opt ballast 3492 [1584 Kg] Play weight does not include added auxiliary equipment. - Page 4 Gared Outer Limit Pro Portable Backstop BASIC DIMENTIONS 9718S, 9718E (10’-8” F.O.B.) Play Weight MODEL lbs [Kg] 9718S w/ std ballast 3535 [1603 Kg] w/ opt ballast 3975 [1803 Kg] 9718E w/ std ballast 3567 [1618 Kg] w/ opt ballast 4007 [1817 Kg] Play weight does not include added auxiliary equipment.
-
Page 5: Cautions And Warnings
Gared Outer Limit Pro Portable Backstop Read and understand the following warnings to prevent possible personal injury and potential damage to the equipment during assembly, setup, and operation. Before proceeding with assembly, read all instructions and assembly procedures. Make sure... -
Page 6: Parts Checklist
Gared Outer Limit Pro Portable Backstop Parts Checklist The following parts have been packed separately or installed on the unit. Verify all parts listed on packing list are present prior to installation. Because these units can use a variety of backboards and goals, the specific part number is not referenced in the table. - Page 7 Gared Outer Limit Pro Portable Backstop...
-
Page 8: Installation
Gared Outer Limit Pro Portable Backstop INSTALLATION INSTRUCTIONS Tools Required: o *½”, 9/16”, ¾”, 15/16” combination wrench o *½”, 9/16”, ¾” deep sockets with ratchet handle o *Allen wrench set o *Bubble type level o *12” Adjustable wrench with 1-1/8” capacity... -
Page 9: Board And Goal Assy
Gared Outer Limit Pro Portable Backstop BOARD AND GOAL ASSY IMPORTANT NOTE: Before proceeding to the next step, make sure at least three individuals are available to assist with the mounting of the backboard to the unit. A minimum of two, preferably three, individuals is required for safe assembly of the backboard to the unit. - Page 10 Gared Outer Limit Pro Portable Backstop 4. Position the backboard and goal assembly with the slots of the Quick Change bracket onto the Quick Change Bracket Pins on the main boom as shown in figure 4,5, and 6. Slide the board assembly completely onto the...
- Page 11 Gared Outer Limit Pro Portable Backstop 7. With board and goal mounted, confirm that the Locking Pin on the Slide Latch Bar is in place as shown in figure 13. Then, remove the (4) ½-13 Hex Bolts to disassemble the Shipping Brace from the main boom and front upright.
-
Page 12: Locating And Adjusting Unit
Gared Outer Limit Pro Portable Backstop LOCATING AND ADJUSTING UNIT 1. Using masking tape and pencil, Mark the location of the center of the court 4’-0” [1219 mm] from the inside edge of the court baseline (refer to figure 10). From this center mark, establish a mark 3’-0”... - Page 13 Gared Outer Limit Pro Portable Backstop 4. To level the backboard in the vertical plane, first loosen the two carriage bolts, item 2, at the Board Brace Clamp, item #15, on top of the boom as shown in figure 12. Using a ¾” wrench, loosen the ½” Jam Nut and adjust the ½”...
- Page 14 Gared Outer Limit Pro Portable Backstop 7. Attach plumb bobs to the front corners of the backboard. Plumb bobs should hang down from the corners to where they are almost touching the floor. 8. Check plumb bobs with marks that were located in step 1. If the plumb bobs do not line up exactly with the marks on the floor, adjust the location of the unit accordingly.
- Page 15 Gared Outer Limit Pro Portable Backstop 15. Using a 1” Fornster or spade bit, drill a 1/8” deep counter-bore at the (2) Locator Pin locations marked on the floor in step 10. Using a ¾” Fornster or spade bit, drill through the rest of the floor (minimum of 1”...
-
Page 16: Pad Installation
Gared Outer Limit Pro Portable Backstop PAD INSTALLATION Figure 23 1. Install (2) Pad Hinge Brackets, item 40.7, to each side of the Front Lower Pad, item 40.2, using ¼-20 Machine Screw and Flat Washer as shown in figure 23, detail F. - Page 17 Gared Outer Limit Pro Portable Backstop 4. Install the Side Pads, item 40.4 and 40.5, by positioning its Pad Clips above the side frame rails and pushing the pad down. Pad Clip, item 40.6, will hook over both the top and bottom frame rails as shown in figure 25.
-
Page 18: Unit Operation
Gared Outer Limit Pro Portable Backstop Operation 1. Before operating the unit, read all caution, warning, and information labels. 2. Position the unit on the floor. a. Position the unit on the court so that the Locator Pins are directly over the Floor Bushings insert. - Page 19 Gared Outer Limit Pro Portable Backstop 4. Install the Locking Turnbuckle by pinning it to the Rear Upright. Lightly tighten the turnbuckle to remove any movement in the Uprights. Figure 30 5. Check that the Front Leveling pad is on the floor and the Front Casters wheels clear the floor as shown in figure 31.
- Page 20 Gared Outer Limit Pro Portable Backstop 7. If the unit is to be moved to storage, a. Lift the Locating Pins and hook in the stored position as shown in figure 33. b. Release the rear Tie Down Bolt. The Tie Down...
-
Page 21: Electric Lift Operation & Wiring Diagram
Gared Outer Limit Pro Portable Backstop Electric Lift Operation (Model 9716E and 9718E) Remote Control Fob Figure 36 1. The E models are equipped with an electric lift system. 2. These models will require a power source of 120vac 60hz or 220vac 50hz. - Page 22 Gared Outer Limit Pro Portable Backstop 9716E and 9718E wiring diagram. SET POWER SUPPLY INPUT VOLTAGE: • Set switch on back of power supply for the appropriate input AC voltage. 115v or 220 v. • Requires 6.5a at 115vac or 3.5a at 220vac.
-
Page 23: Maintenance
Gared Outer Limit Pro Portable Backstop Maintenance 1. General inspection of equipment when used should be performed to ensure no catastrophic failures have occurred during the course of use between yearly inspections. 2. It is recommended that yearly inspections be conducted to determine if any bolts or other hardware has become worn or loosened. -
Page 24: Troubleshooting
Gared Outer Limit Pro Portable Backstop TROUBLESHOOTING (Models 9716, 9718, 9716E, 9718E) 1. Unit is too heavy to lift or does not stay down when lowered down. A. The unit’s spring assist has been adjusted at the factory to lift a specific weight which includes the boom, board, goal, padding, and any shot clock or signage that was specified at the time of the order. - Page 25 Gared Outer Limit Pro Portable Backstop 5. Unit does not hold the correct goal height or board location when returned from storage. a. Be sure unit is returned to its original floor position. Mark each unit to identify it for the specific location on the court as first located and leveled during initial installation.
- Page 26 Gared Outer Limit Pro Portable Backstop 5. Electric actuator does not run. a. Check to see if unit is plugged into power outlet. b. Check that power source to confirm that 115v or 220v is at outlet. c. Check that Safety Pin been removed from...
- Page 27 Gared Outer Limit Pro Portable Backstop...
- Page 28 Gared Holdings, LLC Performance Sports Systems Gared Sports 9200 E. 146 Street 9200 E. 146 Street Noblesville, IN 46060 Noblesville, IN 46060 800-848-8034 800-325-2682 www.perfsports.com www.garedsports.com...
Need help?
Do you have a question about the PSS 9716S and is the answer not in the manual?
Questions and answers