Related Manuals for Gared Hoopmaster LT Portable Backstop
Summary of Contents for Gared Hoopmaster LT Portable Backstop
- Page 1 Hoopmaster LT Portable Backstop Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE Publication No. 5 5 1 7 5 4 0 9 2...
-
Page 2: Table Of Contents
Hoopmaster LT Portable Backstop Table of Contents Section Page No Item List Introduction Cautions and Warnings Assembly and Setup Unit Operation Maintenance - 1 -... -
Page 3: Item List
Hoopmaster LT Portable Backstop Item List Item Part Number Description Refer to Packing List Backboard Refer to Packing List Goal 886404057 Front Main Pad 886404058 Front Bottom Pad 886404055 Left Hand Side Pad 886404056 Right Hand Side Pad 886404059 Rear Top Pad... -
Page 4: Introduction
Hoopmaster LT Portable Backstop Introduction Thank you for purchase of a Gared Sports Hoopmaster LT Portable backstop. To ensure that our equipment will provide years of use to you, we are including this installation, operation and maintenance of your portable backstop. -
Page 5: Cautions And Warnings
GARED Hoopmaster LT Portable Backstop Read and understand the following warnings to prevent possible personal injury and potential damage to the equipment during assembly, setup, and operation. Before proceeding with assembly, read all instructions and assembly procedures. Make sure all parts have been received and are not damaged. -
Page 6: Assembly And Setup
Hoopmaster LT Portable Backstop ASSEMBLY IMPORTANT NOTE: Before proceeding to the next step, make sure at least three individuals are available to assist with the mounting of the backboard to the unit. A minimum of two, preferably three, individuals is required for safe assembly of the backboard to the unit. - Page 7 Hoopmaster LT Portable Backstop TOP MOUNTING YOKE BRACE Figure 3 REAR YOKE BRACE MOUNT 3) Remove the shipping bracket from the main boom and store the bracket, threaded rods, and hardware in a location for future use when replacing backboards or storing the unit.
- Page 8 Hoopmaster LT Portable Backstop SETUP 4) To set the unit the pads must be locked in place. Stepping on them can do this. The pads are found at all four corners. Leveling can be done with the adjustment screw. ADJUSTMENT SCREW SETTING PADS 5) Using masking tape and pencil, Mark the location of the center of the court 4’-0”...
- Page 9 Hoopmaster LT Portable Backstop 7) To level the backboard in the horizontal plane, loosen the two goal carriage bolts and the two 3/8 bolts at the bottom of the board mounting bracket that attach the bracket to the backboard. Level the board and tighten all four bolts securely.
- Page 10 Hoopmaster LT Portable Backstop 11) Once the unit is relocated and the plumb bobs are exactly on the marks located in step 5, recheck all dimensions to make sure the 10’-0” playing height is correct and the face of the backboard is 4’-0” in front of the court baseline.
-
Page 11: Unit Operation
Hoopmaster LT Portable Backstop Operation 1. Before operating the unit, read all caution, warning, and information labels. 2. To raise the unit from the stored position. a. Make sure the unit is in the correct position on the court. b. Remove the safety pin from the slide bar. Loosen the locking knob. -
Page 12: Maintenance
Hoopmaster LT Portable Backstop Maintenance 1. General inspection of equipment when used should be performed to ensure no catastrophic failures have occurred during the course of use between yearly inspections. 2. It is recommended that yearly inspections be conducted to determine if any bolts or other hardware has become worn or loosened.
Need help?
Do you have a question about the Hoopmaster LT Portable Backstop and is the answer not in the manual?
Questions and answers