Subscribe to Our Youtube Channel
Related Manuals for Gared 2400
Summary of Contents for Gared 2400
- Page 1 UP FOLD WALL MOUNT Models: 2400 Operation and Maintenance Instructions Please read all instructions before attempting operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE Issued UBLICATION 501756256 10-31-2018...
- Page 2 Maintenance Introduction Thank you for your purchase of a Model 2400 Up Folding Wall Mount Backstop. To ensure that our equipment will provide years of use to you, we are including this operation, and maintenance guide. This guide will provide information on the proper operating procedures, and preventative maintenance of your gymnasium up folding wall mount backstop.
- Page 3 SET SCREW, FLAT POINT 3/8-16 UNC X 0.375 545-8-13 HEX NUT, NYLON LOCK 1/2-13 548-6-16 HEX NUT, SERRATED FLANGE 3/8-16 561-6 FLAT WASHER 3/8 571-4-20-14 SELF TAPPING SCREW, 1/4-20 UNC X 0.875 3125-30-00 1/4" CABLE THIMBLE 501756256 MANUAL, 2400 UP FOLD WALL MOUNT...
-
Page 4: Installation Preparation
UP FOLDING WALL MOUNT Optional Accessories Sold Separately: 1123 Manual Winch 1194 Electric Winch 1100WM SAFSTOP Locate, identify and count all parts before starting the installation to ensure that all are correct and correspond to the packing list/production drawings. If any parts are missing or damaged, DO NOT SUBSTITUTE. - Page 5 UP FOLDING WALL MOUNT UNIT LOADING INFORMATION...
-
Page 6: Tools Required
UP FOLDING WALL MOUNT TOOLS REQUIRED Plumb Bob or Laser Level Electric Drill Drill bits – 7/16”, 9/16”, 5/8” Hammer Wrenches – 1/2", 9/16”, 11/16, and 3/4" Ratchet Wrenches with 1/2", 9/16”, 11/16, and 3/4" sockets File 4’ Level 25’ Tape measure Duct Tape Block of wood (for tapping) Broom... -
Page 7: Installation
UP FOLDING WALL MOUNT INSTALLATION Installation instructions below are general in nature. Your exact installation needs to follow the parts and any specific instruction included in your specific project’s production drawings. 1. Before installing the wood pads on the wall, you must first preassemble the hinge brackets and chain brackets onto the wood bucks. - Page 8 UP FOLDING WALL MOUNT WOOD PAD LOCATIONS Always refer to specific dimensions outlined in the production drawings shipped for the specific project. Dimensions of the specific project may vary from the dimensions outlined below. The upper wood pad with the chain anchors should be mounted in the same plane as the two frame mounting wood pads.
- Page 9 UP FOLDING WALL MOUNT WOOD PAD WALL ATTACHMENT When attaching the wood pads to the wall, it is important to place the anchors in a location that will not reduce the strength of the wood. Anchors should be ½” diameter and the holes in the wood pads should be no larger than 9/16”...
- Page 10 UP FOLDING WALL MOUNT Install the outer pipe weldments to the hinge points on the lower two wood pads. Install the bushings (Item 6) into both sides of the pipe before installing the pipe into the hinge bracket. Once the pipe has been installed into the hinge bracket and the ½” x 3 1/2” bolt is installed, add the ½”...
- Page 11 UP FOLDING WALL MOUNT Install the pull up cross tube (Item 13) onto the top extension tubes. Note the 3/8 x 2”, 3/8 x 2-3/4” carriage bolts, and the 3/8” whiz-lock nuts are supplied with item 14 and are not listed in the parts list.
- Page 12 UP FOLDING WALL MOUNT Install the cross bracing on the lower extension arms. Refer to the illustration below for the correct attachment method. Note the 3/8 x 2”, 3/8 x 1-1/4” carriage bolts, and the 3/8” whiz-lock nuts are supplied with item 16 and are not listed in the parts list.
- Page 13 UP FOLDING WALL MOUNT INSTALLING THE BACKBOARD WITHOUT A HEIGHT ADJUSTER Raise the arms to as close to level as possible and support the outer portion of the lower extension arms with the scissor lift or scaffolding. Attach the lower corners of the backboard to the lower extension arms first to help stabilize the backboard while...
- Page 14 UP FOLDING WALL MOUNT Slide the pull up tube on the upper extension arms until the center of the tube is Dim “C” from the upper wood pad. Make sure the tube is parallel with the face of the backboard. Tighten the clamp bolts on the tube clamps securely.
- Page 15 UP FOLDING WALL MOUNT INSTALLING THE BACKBOARD WITH A HEIGHT ADJUSTER Raise the arms to as close to level as possible and support the outer portion of the lower extension arms with the scissor lift or scaffolding. Attach the height adjuster frame using the 3/8 x 1 ½”...
- Page 16 UP FOLDING WALL MOUNT Once the height adjuster and backboard has been installed, final adjustments to the FOB and chain tension can be made. Check to make sure each side of the frame is still square to the wall. Measure the distance from the wall to the face of the back board on each side.
- Page 17 UP FOLDING WALL MOUNT Install the locking bolts on the extension arms the prevent movement of the arms. Drill a 7/16” hole through the inner extension tube using the hole in the outer tube as a guide. Install the 3/8” bolt (Item 26), locknut (Item 30) and tighten securely. Repeat the process on all four extension tubes.
- Page 18 UP FOLDING WALL MOUNT Hoist Locations The hoist locations are dependent upon the building conditions, and customer preference; however, it is important to place the hoist in a location that is best for the operation of the backstop and yet relatively easy access for maintenance.
- Page 19 UP FOLDING WALL MOUNT ATTENTION: INSTALLER To confirm that you have received all the parts, and to better serve you if you contact us, please fill out the following information and fax or mail to the address below. Please refer to the facility name and/or the installation company below when you contact the factory, and include it on any correspondence.
- Page 20 UP FOLDING WALL MOUNT Model 2400 Installation Checklist Date: ________________ Unit Number Building structure has been approved for unit loads. Attachment anchor system has been approved for the unit loads and installed per the structural engineer’s specifications. Washers have been installed under wood pad’s carriage bolts.
- Page 21 UP FOLDING WALL MOUNT OPERATING INSTRUCTIONS For all folding backstops, only trained personnel should operate the units. Keep the areas below and around the units clear at all times while the unit is in motion Always use the equipment in the manner intended. The manufacturer does not assume any liability for improperly used or improperly maintained equipment.
- Page 22 Check the wood pads and wood pad wall anchors. Make sure wood pads are not loose to the wall. Make sure wood pads are not cracked or split. This Model #2400 Up Folding wall mount has been custom manufactured according to the Owner’s/Architect’s specifications. When operated and maintained with proper care, this backstop...
- Page 23 UP FOLDING WALL MOUNT ATTENTION: MAINTENANCE DEPARTMENT To confirm that you have received maintenance and warranty information, and to better serve you if you contact us, please fill out the following information and fax or mail to the address below. Please refer to the facility name and/or the installation company below when you contact Performance Sports Systems, and include it on any correspondence.
- Page 24 UP FOLDING WALL MOUNT Maintenance Check Sheet Refer to Maintenance Overview (page 21) for recommended inspection frequency. Date:________________ Unit:___________________ Wood Pads / Anchors -Wood pads, splitting, chipping, etc. Repair Replace -Anchors/Bolts Repair Replace Unit Supports / Brackets / Hinges -Tubes; dents, stress spots, etc. Repair Replace -Bolts;...
- Page 25 Gared Holdings, LLC Performance Sports Systems Gared Sports 9200 E. 146 Street 9200 E. 146 Street Noblesville, IN 46060 Noblesville, IN 46060 800-848-8034 800-325-2682 www.perfsports.com www.garedsports.com...
Need help?
Do you have a question about the 2400 and is the answer not in the manual?
Questions and answers