Table of Contents
Advertisement
Allure™ EC-Smart-Comfort Series
Product Description
The Allure EC-Smart-Comfort Series are versatile communicating sensors which provide precise temperature sensing.
Tailored for occupants, the Allure EC-Smart-Comfort Series' intuitive design features coloured LED indicators to provide user feedback, rotary knobs to
adjust the setpoint offset and fan speed, and a push-button to apply occupancy override.
As a multi-function room device, the Allure EC-Smart-Comfort Series sensor can be expanded with a combination of up to 4 Smart-Light/Blind Series
add-on push-button modules, for lighting and shade/sunblind control, making it an ideal all-in-one addition to the Smart Room Control solution.
This document describes the hardware installation procedures for the Allure EC-Smart-Comfort sensors. This line of communicating sensors is com-
posed of the following models:
£
Allure EC-Smart-Comfort-S
£
Allure EC-Smart-Comfort-S-DI
£
Allure EC-Smart-Comfort-SO
£
Allure EC-Smart-Comfort-SO-DI
£
Allure EC-Smart-Comfort-SF
£
Allure EC-Smart-Comfort-SF-DI
£
Allure EC-Smart-Comfort-SOF
£
Allure EC-Smart-Comfort-SOF-DI
This document also covers the installation of the Smart-Light/Blind Series add-on modules.
General Installation Requirements
For proper installation and subsequent operation of the device, pay special attention to the following recommendations:
£
It is recommended that the product(s) be kept at room temperature for at least 24 hours before installation to allow any condensation that may have
accumulated due to low temperature during shipping/storage to evaporate.
£
Upon unpacking the product, inspect the contents of the carton for shipping damages. Do not install damaged modules.
£
The device is designed to operate under such environmental conditions as specified in its datasheet.
£
Ensure proper ventilation of the device and avoid areas where corroding, deteriorating or explosive vapors, fumes or gases may be present.
£
Do not drop the device or subject it to physical shock.
£
If the device is used and/or installed in a manner not specified by Distech Controls, the functionality and the protection provided by the device may
be impaired.
£
To ensure reading accuracy, handle the sensor with care, and avoid installing it on a vibrating surface.
Make connections to the product last. Yanking the cable while it is attached to the product can damage the
connector.
Any type of modification to any Distech Controls product will void the product's warranty.
Take reasonable precautions to prevent electrostatic discharges to the product when installing, servicing, or
operating it. Discharge any accumulated static electricity by touching a grounded object with your hand before
handling the product.
I n s t a l l a t i o n G u i d e
Advertisement
Table of Contents
Related Manuals for Distech Controls Allure EC-Smart-Comfort Series
Summary of Contents for Distech Controls Allure EC-Smart-Comfort Series
- Page 1 Do not drop the device or subject it to physical shock. £ If the device is used and/or installed in a manner not specified by Distech Controls, the functionality and the protection provided by the device may be impaired. £...
-
Page 2: Device Markings
Device Markings Certain markings (symbols) can be found on the side of the product and are defined as follows: Symbol Description CE marking: the device conforms to the requirements of applicable EC directives. UKCA marking: the device conforms to the requirements of applicable Great Britain regulations. UL marking: conforms to the requirements of the UL certification. - Page 3 Figure 2: Allure EC-Smart-Comfort - Back plate view Figure 3: Smart-Light/Blind add-on modules - Front view and side view 3 / 13...
-
Page 4: Device Components
Figure 4: Smart-Light/Blind add-on modules - Back plate view Device Components Figure 5: Allure EC-Smart-Comfort Sensor - Front elements Figure 6: Allure EC-Smart-Comfort Sensor - Bottom elements Mounting Instructions This product has been specifically designed for easy installation. However, certain conditions apply when choosing a suitable location for the device: £... - Page 5 Installation Procedure 1. Remove the security screw from the device. 2. Open the device by pushing in the tab on its bottom and then by pulling the bottom side of the front plate out. 3. Open the Smart-Light/Blind Series module by pulling the front plate off (if applicable). 4.
- Page 6 Wiring the Allure EC-Smart-Comfort with a Digital Input Cable The following models feature a digital input cable: £ Allure EC-Smart-Comfort-S-DI £ Allure EC-Smart-Comfort-SO-DI £ Allure EC-Smart-Comfort-SF-DI £ Allure EC-Smart-Comfort-SOF-DI The digital input cable is provided unplugged, and it is to be connected into the sensor when mounting the device (see section Mounting Instructions [pg. 4]).
- Page 7 Figure 8: Example: connection of a 2-pole switch (i.e. ON-OFF light switch) and a 3-point switch (UP/DOWN lighting or shade switch) to an Allure EC-Smart-Comfort sensor equipped with 2 Smart-Light/Blind modules The allocation of digital inputs to the Smart-Light/Blind Series add-on modules is not configurable: the closest module to the Allure EC- Smart-Comfort sensor automatically uses Digital Inputs 1 and 2, the next one uses Digital Inputs 3 &...
- Page 8 The Allure EC-Smart-Comfort Series and Allure EC-Smart-Air Series sensors share the same Subnet ID range: the same address CANNOT be concurrently assigned to an Allure EC-Smart-Comfort Series sensor AND to an Allure EC-Smart-Air Series sensor.
- Page 9 The indicated addressing ranges are specific to each group of devices. 4 different Subnet ID codifications are used on the ECx Subnetwork : £ 1 for Allure EC-Smart-Vue Series sensors £ 1 for Allure EC-Smart-Comfort and Allure EC-Smart-Air sensors £ 1 for EC-Multi-Sensors £...
- Page 10 Subnetwork Bus Topology and EOL Terminations Only a daisy-chain topology is acceptable for the room device subnetwork bus. T-connections are not allowed. ECB/ECL-VAVS, ECB/ECL-VAV-N, ECB/ECL-103, ECB/ECL-203, ECB/ECL-300, ECB/ECL-400 For controllers other than ECB-600 or ECL-600 series controllers, only the EOL terminations of the last subnetwork bus device must be set to ON. All other subnetwork bus devices must have their EOL terminations set to OFF.
- Page 11 ECB/ECL-VAV, ECB/ECL-PTU, ECY-S1000, ECY-VAV, ECY-303, ECY-PTU Figure 11: Setting the EOL Terminations on the Allure EC-Smart-Comfort Sensor for Smart Room Control controllers ECB/ECL-600 When one or more room devices are installed with an ECB-600 or ECL-600 series controller (without an ECx-4xx O Extension Module) controller: £...
- Page 12 ECB/ECL-600 With ECx-400 When ECx-4xx IO Extension Modules are installed with an ECB-600 or ECL-600 Series controller and with room device(s): £ Only the EOL terminations on the last ECx-4xx IO Extension Module and the last room device are set to ON. £...
-
Page 13: Maintenance And Cleaning
©, Distech Controls Inc., 2015 - 2022. All rights reserved. Images are simulated. While all efforts have been made to verify the accuracy of information in this manual, Distech Controls is not responsible for damages or claims arising from the use of this manual.
Need help?
Do you have a question about the Allure EC-Smart-Comfort Series and is the answer not in the manual?
Questions and answers