Advertisement
1
WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2
Close all vehicle doors, hood and trunk.
Press the LOCK button once [1x] on the aftermarket keyfob.
3
Question 1: Do the doors lock?
YES: Go to next step.
¨
NO: Verify the remote programming, the RF connections and the wired door lock/unlock
connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
¨
technical support, if the problem persists.
Press the UNLOCK button once [1x] on the aftermarket keyfob.
4
Question 2: Do the doors unlock?
YES: Go to next step.
¨
NO: Verify the remote programming, the RF connections and the wired door lock/unlock
connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
¨
technical support, if the problem persists.
Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
5
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
¨
NO: Verify the remote programming, the RF connections and the wired trunk/hatch
connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
¨
technical support, if the problem persists.
Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
6
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
¨
NO: Verify the remote programming and the RF connections. Repeat the test and call
¨
technical support, if the problem persists.
7
Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
¨
NO: Verify the remote programming and the RF connections. Repeat the test and call
¨
technical support, if the problem persists.
Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
8
Question 6: Does the vehicle remote start?
YES: Go to next step.
¨
NO: Verify the remote programming, the RF connections and check the remote start error
¨
codes. Repeat the test and call technical support, if the problem persists.
Patent No. US 8,856,780 CA 2759622
Automotive Data Solutions Inc. © 2022
INSTALLATION CHECKLIST - 1 OF 1
CHECKLIST
9
Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
¨
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle
¨
and call technical support.
10
RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after
remote start shutdown?
YES: Go to next step.
¨
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the
¨
test and call technical support if the problem persists.
11
Open hood.
If not already installed, affi x the mandatory orange warning sticker under the hood and
12
proceed to next step.
Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
13
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood
switch, then repeat the test.
¨
NO: Go to next step.
¨
14
Close hood.
15
Enter vehicle and close the doors.
Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
16
17
Wait for the vehicle to start.
18
Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
¨
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once
[1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the
¨
wiring diagram, if applicable, and call technical support.
19
Exit vehicle.
20
Installation checklist completed.
FLCI-CH(RS)-CH8-[FLRSCH7]-EN
PAGE 22 OF 22
• 20221216
DOC.: #81143
www.flashlogic.com
Advertisement
