Advertisement

Quick Links

HCD-EC709iP/EC909iP
SERVICE MANUAL
Ver. 1.0 2010.03
• HCD-EC709iP is the amplifi er, CD player, tuner
and iPod/iPhone section in MHC-EC709iP.
• HCD-EC909iP is the amplifi er, CD player, tuner
and iPod/iPhone section in MHC-EC909iP.
 iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
 iPhone is a trademark of Apple Inc.
 MPEG Layer-3 audio coding technology and patents
licensed from Fraunhofer IIS and Thomson.
 All other trademarks and registered trademarks are of
®
their respective holders. In this manual,
TM
and
marks
are not specified.
Main unit
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
(The United States model only)
Front Speaker
With 12 ohm loads, both channels driven, from 120 – 10,000 Hz;
rated 70 watts per channel minimum RMS power, with no more than
0.7% total harmonic distortion from 250 milliwatts to rated output.
Amplifier section
The following measured at AC 120 V, 60 Hz
(North American model)
The following measured at AC 240 V, 50/60 Hz
(Australian model)
HCD-EC909iP
North American model:
Front Speaker
RMS output power (reference):
180 W + 180 W (per channel at 12 Ω, 1 kHz)
Subwoofer
RMS output power (reference):
180 W (at 12 Ω, 80 Hz)
Australian model:
Front Speaker
Power output (rated):
85 W + 85 W (at 12 Ω, 1 kHz, 1% THD)
RMS output power (reference):
180 W + 180 W (per channel at 12 Ω, 1 kHz)
Subwoofer
RMS output power (reference):
180 W (at 12 Ω, 80 Hz)
HCD-EC709iP
North American model:
RMS output power (reference):
180 W + 180 W (per channel at 12 Ω, 1 kHz)
Australian model:
Power output (rated):
85 W + 85 W (at 12 Ω, 1 kHz, 1% THD)
RMS output power (reference):
180 W + 180 W (per channel at 12 Ω, 1 kHz)
Inputs
PC IN (stereo mini jack): Sensitivity 800 mV, impedance 22 kilohms
Outputs
SPEAKERS: Impedance 12 Ω
SUBWOOFER (MHC-EC909iP only): Impedance 12 Ω
Sony Corporation
9-889-760-01
2010C05-1
Audio&Video Business Group
©
2010.03
Published by Sony Techno Create Corporation
Photo: HCD-EC909iP
SPECIFICATIONS
CD player section
System: Compact disc and digital audio system
Laser Diode Properties
Emission Duration: Continuous
Laser Output*: Less than 44.6μW
* This output is the value measurement at a distance of 200mm
from the objective lens surface on the Optical Pick-up Block
with 7mm aperture.
Frequency response: 20 Hz − 20 kHz
Signal-to-noise ratio: More than 90 dB
Dynamic range: More than 88 dB
Tuner section
FM stereo, FM/AM superheterodyne tuner
Antenna:
FM lead antenna
AM loop antenna
FM tuner section:
Tuning range
North American model: 87.5 MHz − 108.0 MHz (100 kHz step)
Australian model: 87.5 MHz − 108.0 MHz (50 kHz step)
Intermediate frequency: 225 kHz
AM tuner section:
Tuning range
North American model:
530 kHz − 1,710 kHz (10 kHz step)
531 kHz − 1,710 kHz (9 kHz step)
Australian model:
531 kHz − 1,710 kHz (9 kHz step)
530 kHz − 1,710 kHz (10 kHz step)
Intermediate frequency: 53 kHz
Model Name Using Similar Mechanism
Base Unit Name
Optical Pick-up Block Name
iPod/iPhone section
General
Compatible iPod/iPhone models:
Power requirements:
North American model: AC 120 V, 60 Hz
Australian model: AC 230 V − 240 V, 50/60 Hz
Power consumption:
HCD-EC909iP
North American model: 250 W
Australian model: 250 W
iPhone 3GS
iPhone 3G
iPhone
(0.5 W at the Power Saving Mode)
HCD-EC709iP
North American model: 200 W
Australian model: 200 W
(0.5 W at the Power Saving Mode)
Dimensions (W/H/D) (excl. speakers):
iPod nano
Approx. 200 mm × 306 mm × 389 mm
iPod classic
5th generation
iPod touch
120GB
Mass (excl. speakers):
(video camera)
2nd generation
160GB (2009)
HCD-EC909iP
Approx. 5.7 kg
HCD-EC709iP
Approx. 5.5 kg
Design and specifications are subject to change without notice.
iPod nano
iPod classic
4th generation
iPod touch
160GB (2007)
(video)
1st generation
Standby power consumption: 0.5 W
Halogenated flame retardants are not used in the certain printed
wiring boards.
iPod nano
3rd generation
iPod nano
iPod classic
(video)
2nd generation
80GB
(aluminum)
iPod nano
iPod
iPod
1st generation
5th generation
4th generation
(video)
(color display)
iPod mini
iPod
4th generation
COMPACT DISC RECEIVER
US Model
Canadian Model
Australian Model
NEW
BU-D1BD73
DA11MMVGP

Advertisement

Table of Contents
loading

Summary of Contents for Sony HCD-EC709iP

  • Page 1 SERVICE MANUAL US Model Canadian Model Ver. 1.0 2010.03 Australian Model • HCD-EC709iP is the amplifi er, CD player, tuner and iPod/iPhone section in MHC-EC709iP. • HCD-EC909iP is the amplifi er, CD player, tuner and iPod/iPhone section in MHC-EC909iP. Photo: HCD-EC909iP ...
  • Page 2 LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC- TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON- NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
  • Page 3: Table Of Contents

    HCD-EC709iP/EC909iP TABLE OF CONTENTS SERVICING NOTES 5-5. Schematic Diagram - BD73 Board - ....... 19 ..........5-6. Printed Wiring Boards - iPod & iPhone, JACK Section - ........20 DISASSEMBLY 5-7. Schematic Diagram 2-1. Disassembly Flow ............- iPod & iPhone, JACK Section - ........21 2-2.
  • Page 4: Servicing Notes

    HCD-EC709iP/EC909iP SECTION 1 SERVICING NOTES MODEL IDENTIFICATION NOTES ON HANDLING THE OPTICAL PICK-UP - Back Panel - BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electro- static break-down because of the potential difference generated by the charged electrostatic load, etc.
  • Page 5 HCD-EC709iP/EC909iP CAPACITOR ELECTRICAL DISCHARGE PROCESSING When checking the board, the electrical discharge is necessary for the electric shock prevention. Connect the resistors referring to the fi gure below. • POWER board (C103, C104) Both ends of respective capacitors. – POWER Board (Conductor Side) –...
  • Page 6: Disassembly

    HCD-EC709iP/EC909iP SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. 2-1. DISASSEMBLY FLOW 2-2. SIDE PANEL (L)/(R) 2-3. ORNAMENT PLATE (DOCK) OR iPod ASSY (Page 6) (Page 7) 2-5. TOP PANEL BLOCK 2-4. IP BOARD BLOCK, BASE (DOCK) BLOCK...
  • Page 7: Ornament Plate (Dock) Or Ipod Assy

    HCD-EC709iP/EC909iP 2-3. ORNAMENT PLATE (DOCK) OR iPod ASSY 2 Push in flat-head screwdriver. Note 1: Avoid a claw and put a flat-head screwdriver in. 3 claw 2 Push in flat-head screwdriver. 1 Open the iPod dock. Note 1: Avoid a claw and put a flat-head screwdriver in.
  • Page 8: Ip Board Block, Base (Dock) Block

    HCD-EC709iP/EC909iP 2-4. IP BOARD BLOCK, BASE (DOCK) BLOCK Note 1: This illustration sees the front panel from bottom side. 1 four screws (B2.6) Never put the sheet to the claw. 5 Remove two solders. 6 IP board block 2 sheet...
  • Page 9: Back Panel Block

    HCD-EC709iP/EC909iP 2-6. BACK PANEL BLOCK (EC909iP) 3 screw (BVTP3 3 screw (BVTP3 4 back panel block 3 three screws (BVTP3 2 fan connector (CN051) 1 Cut the wire holder. Note: In reassembling, use new wire holder to fasten the wire holder same as before.
  • Page 10: Front Panel Block

    HCD-EC709iP/EC909iP 2-8. FRONT PANEL BLOCK 3 Remove clamping. 5 sheet 1 flexible flat cable (25 core) 9 front panel block (CN603) Note 1: Confirm it is unquestionable for the open/close of the iPod dock after the lead wire is processed.
  • Page 11: Base Unit (Bu-D1Bd73)

    HCD-EC709iP/EC909iP 2-10. BASE UNIT (BU-D1BD73) Note 1: This illustration sees the top panel block from base unit side. (EC709iP) 5 two vibration proof rubbers 2 stopper (D1) (green) 1 four floating screws (PTPWHM2.6) 8 base unit 4 two vibration proof rubbers...
  • Page 12: Test Mode

    HCD-EC709iP/EC909iP SECTION 3 TEST MODE COLD RESET CD SERVICE MODE The cold reset clears all data including preset data stored in the This mode can move the SLED of the optical pick-up, and also can memory to initial conditions. Execute this mode when returning turn the optical pick-up laser power on and off.
  • Page 13: Electrical Check

    HCD-EC709iP/EC909iP SECTION 4 ELECTRICAL CHECK [iPod & iPhone]: Note: 1. CD Block is basically constructed to operate without adjustment. Tracking servo setting changes whenever the button is pressed 2. Use YEDS-18 disc (Part No. 3-702-101-01) unless otherwise indicat- (This function is executable only while CD is playing).
  • Page 14: Diagrams

    HCD-EC709iP/EC909iP SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAM - CD SERVO, TUNER Section - CN082 ANTENNA FM/AM BAND-PASS FILTER 30 FM ANT L-OUT TUNER-L FL081 (Page 15) R-OUT R-CH AM/FM-DET, OSC, MIX, PLL, IF AMP L081 IC081 1 AM ANT : TUNER (FM/AM)
  • Page 15: Block Diagram - Main Section

    HCD-EC709iP/EC909iP 5-2. BLOCK DIAGRAM - MAIN Section - R-ch is omitted due to same as L-ch. SIGNAL PATH : TUNER (FM/AM) : CD PLAY : iPod & iPhone ELECTRICAL VOLUME, : PC IN INPUT SELECTOR IC601 TB701 RY701 J491 R-CH...
  • Page 16: Block Diagram - Panel, Power Supply Section

    HCD-EC709iP/EC909iP 5-3. BLOCK DIAGRAM - PANEL, POWER SUPPLY Section - FAN MOTOR FAN-CONT DRIVE Q052 - 054 DETECT Q051 FAN PROTECT M001 DETECT (FAN) Q071 - 073 D106, 107 (Page 15) PROTECT DETECT Q101, 102 D110 PROTECT DETECT Q103 D111 X301 32.768kHz...
  • Page 17 HCD-EC709iP/EC909iP THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. • Circuit Boards Location (In addition to this, the necessary note is printed in each block.) For Printed Wiring Boards. For Schematic Diagrams. BD73 board Note: Note: MAIN board •...
  • Page 18: Printed Wiring Board - Bd73 Board

    HCD-EC709iP/EC909iP 5-4. PRINTED WIRING BOARD - BD73 Board - • See page 17 for Circuit Boards Location. • : Uses unleaded solder. BD73 BOARD (CONDUCTOR SIDE) BD73 BOARD (COMPONENT SIDE) C301 CL119 CL117 CL419 (VREF) S001 (LIMIT) CL420 SL304 R304...
  • Page 19: Schematic Diagram - Bd73 Board

    HCD-EC709iP/EC909iP 5-5. SCHEMATIC DIAGRAM - BD73 Board - • See page 30 for Waveforms. • See page 30 for IC Block Diagrams. BD73 BOARD C136 C116 C132 R413 C133 C131 C130 R125 C127 C129 C128 R126 CN201 C201 CL118 VREF...
  • Page 20: Printed Wiring Boards - Ipod & Iphone, Jack Section

    HCD-EC709iP/EC909iP 5-6. PRINTED WIRING BOARDS - iPod & iPhone, JACK Section - • See page 17 for Circuit Boards Location. • : Uses unleaded solder. (EC909iP) D902, 906 PANEL BOARD D902, 906 IP BOARD CN302 IP BOARD Dock for iPod...
  • Page 21: Schematic Diagram - Ipod & Iphone, Jack Section

    HCD-EC709iP/EC909iP 5-7. SCHEMATIC DIAGRAM - iPod & iPhone, JACK Section - IP BOARD IC901 EEPROM IC901 MFI341S2164 11 12 13 14 15 (EC909iP) D902, 906 C910 C905 CN902 0.01 Dock for iPod (iPod/iPhone CONNECTOR) (iPod INDICATOR) PGND JL001 DGND POWER...
  • Page 22: Printed Wiring Board - Main Board (Component Side)

    HCD-EC709iP/EC909iP 5-8. PRINTED WIRING BOARD - MAIN Board (Component Side) - • See page 17 for Circuit Boards Location. • : Uses unleaded solder. MAIN BOARD (COMPONENT SIDE) (EC909iP) R852 R851 C856 C854 R745 Q704 Q703 JR802 C872 Q805 C871...
  • Page 23: Printed Wiring Board - Main Board (Conductor Side)

    HCD-EC709iP/EC909iP 5-9. PRINTED WIRING BOARD - MAIN Board (Conductor Side) - • See page 17 for Circuit Boards Location. • : Uses unleaded solder. MAIN BOARD (CONDUCTOR SIDE) (EC909iP) TP608 IC611 TP605 C738 C740 C739 (CHASSIS) C780 IC604 JR702 A001...
  • Page 24: 5-10. Schematic Diagram - Main Board (1/2)

    HCD-EC709iP/EC909iP 5-10. SCHEMATIC DIAGRAM - MAIN Board (1/2) - • See page 30 for IC Block Diagrams. MAIN BOARD (1/2) R616 IC B/D Q701-704 OVER LOAD DETECT R740 IC604 Q701 POWER AMP R741 2SA2026 2.2k IC604 STK433-870-E R739 C741 1.2k...
  • Page 25: Schematic Diagram - Main Board (2/2)

    HCD-EC709iP/EC909iP 5-11. SCHEMATIC DIAGRAM - MAIN Board (2/2) - • See page 30 for IC Block Diagrams. MAIN BOARD (2/2) R098 C092 C1082 R099 X081 180k 32.768kHz D082 R091 TP669 I-TU-DO MC2840-T112-1 R092 TP668 FL081 O-TU-CLK R093 TP667 O-TU-DI R094...
  • Page 26: 5-12. Printed Wiring Board - Panel Board

    HCD-EC709iP/EC909iP 5-12. PRINTED WIRING BOARD - PANEL Board - • See page 17 for Circuit Boards Location. • : Uses unleaded solder. LCD301 LIQUID CRYSTAL DISPLAY R341 R394 Q301 JW304 JW305 R393 R345 JW360 X302 R410 C333 IC302 R342 R313...
  • Page 27: 5-13. Schematic Diagram - Panel Board

    HCD-EC709iP/EC909iP 5-13. SCHEMATIC DIAGRAM - PANEL Board - • See page 30 for Waveforms. • See page 32 for IC Pin Function Description. PANEL BOARD CN301 JL301 D303 PC-IN-L 1L0341Y23E0CA602-II (EC709iP) SELG2WA10C LF62 (EC909iP) X302 PC-IN-GND 6MHz JL302 PC-IN-R Q306...
  • Page 28: 5-14. Printed Wiring Board - Power Board

    HCD-EC709iP/EC909iP 5-14. PRINTED WIRING BOARD - POWER Board - • See page 17 for Circuit Boards Location. • : Uses unleaded solder. M001 (FAN) CN051 LP001 TP052 TP051 POWER BOARD Q052 R071 R072 Q053 R061 R060 R059 D052 R055 C001...
  • Page 29: 5-15. Schematic Diagram - Power Board

    HCD-EC709iP/EC909iP 5-15. SCHEMATIC DIAGRAM - POWER Board - • See page 30 for IC Block Diagrams. POWER BOARD Q052-054 FAN MOTOR DRIVE Q053 KTA1273-Y-AT 13.9 CN102 Q071-073 R061 R060 R059 FAN PROTECT DETECT TP121 CD-AVR TP122 13.3 D109 I-P-MONI MA2J1110GLS0...
  • Page 30 HCD-EC709iP/EC909iP • Waveforms IC301 BA5826SFP-E2 – BD73 Board – – PANEL Board – VO1(–) D.BUFF IC101 2 (RFOUT) IC301 qf (X1A) VO4(–) VO1(+) D.BUFF (CD play mode) D.BUFF LEVEL SHIFT VO4(+) D.BUFF LEVEL SHIFT RESET 3.1 Vp-p 0.7 to 1.5 Vp-p 30.6 s...
  • Page 31 HCD-EC709iP/EC909iP IC601 BD3499FV-E2 IC604 STK433-870-E IC606 STK433-070-S-E 28 FIL INPUT INPUT 27 GND GAIN SELECTOR PRE DRIVE 26 SDA PC BUS FINAL DRIVE PRE DRIVE LOGIC 25 SCL SEL2 INVERTER FINAL DRIVE STANDBY SEL1 24 VCC CIRCUIT VOL1 VOLUME VOL2...
  • Page 32 HCD-EC709iP/EC909iP • IC Pin Function Description PANEL BOARD IC301 MB90F830PF-GE1 (SYSTEM CONTROLLER) Pin No. Pin Name Description SEG32 Segment drive signal output to the liquid crystal display O-SP-RELAY Relay drive signal output terminal (for speaker) O-POWER Main power on/off control signal output terminal “H”: main power on...
  • Page 33 HCD-EC709iP/EC909iP Pin No. Pin Name Description 63, 64 SEG0, SEG1 Segment drive signal output to the liquid crystal display Power supply terminal (+3.3V) Ground terminal 67 to 89 SEG2 to SEG24 Segment drive signal output to the liquid crystal display Power supply terminal (+3.3V)
  • Page 34: Exploded Views

    HCD-EC709iP/EC909iP SECTION 6 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so • The mechanical parts with no reference The components identifi ed by mark 0 they may have some difference from the number in the exploded views are not sup- or dotted line with mark 0 are critical for original one.
  • Page 35: Top Panel Section

    HCD-EC709iP/EC909iP 6-2. TOP PANEL SECTION not supplied S351 (including sled motor, spindle motor) not supplied not supplied (spindle motor) not supplied not supplied (sled motor) (EC709iP) S001 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1748-697-A...
  • Page 36: Front Panel Section

    HCD-EC709iP/EC909iP 6-3. FRONT PANEL SECTION not supplied (JACK HOLD board) not supplied (JACK board) not supplied not supplied (COVER board) Note: The hole of the front panel that passes the fl exible fl at cable (13 core) and the wire from the IP board block is different.
  • Page 37: Ipod Dock Section

    HCD-EC709iP/EC909iP 6-4. iPod DOCK SECTION not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-120-664-02 PLATE, ORNAMENT (DOCK) (EC709iP) 3-277-576-01 ESCUTCHEON X-2348-584-1 IPOD ASSY (EC909iP) 4-120-666-01 LOCK (DOCK) 3-253-143-01 SCREW (B2.6), (+) P TAPPING...
  • Page 38: Main Board Section

    HCD-EC709iP/EC909iP 6-5. MAIN BOARD SECTION Note: Cover (tuner top) and cover (function top) cannot re-used. When these parts are removed, new parts must be replaced. (EC909iP) (EC909iP) not supplied not supplied not supplied #1 #1 not supplied not supplied M001 chassis section Ref.
  • Page 39: Chassis Section

    HCD-EC709iP/EC909iP 6-6. CHASSIS SECTION not supplied (POWER board) not supplied PT004 (AC HOLD board) not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-162-453-01 CHASSIS (US) 0 254 1-834-967-21 CORD, POWER (AUS) 4-162-453-11 CHASSIS (CND)
  • Page 40: Electrical Parts List

    HCD-EC709iP/EC909iP SECTION 7 BD73 ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in • CAPACITORS When indicating parts by reference num- the parts list may be different from the uF: μF ber, please include the board name. parts specifi ed in the diagrams or the com- •...
  • Page 41 HCD-EC709iP/EC909iP BD73 JACK MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R201 1-218-446-11 METAL CHIP 1/10W R909 1-218-895-11 METAL CHIP 100K 0.5% 1/10W R202 1-216-789-11 METAL CHIP 1/10W R910 1-218-892-11 METAL CHIP 0.5% 1/10W R203...
  • Page 42 HCD-EC709iP/EC909iP MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C606 1-162-964-11 CERAMIC CHIP 0.001uF C671 1-164-227-11 CERAMIC CHIP 0.022uF C607 1-162-968-11 CERAMIC CHIP 0.0047uF C672 1-162-964-11 CERAMIC CHIP 0.001uF C608 1-162-970-11 CERAMIC CHIP 0.01uF C673 1-110-563-11 CERAMIC CHIP 0.068uF...
  • Page 43 HCD-EC709iP/EC909iP MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C732 1-100-566-91 CERAMIC CHIP 0.1uF C794 1-164-858-11 CERAMIC CHIP 22PF C733 1-128-991-21 ELECT CHIP 10uF C801 1-124-779-00 ELECT CHIP 10uF (EC909iP) C734 1-128-991-21 ELECT CHIP 10uF...
  • Page 44 HCD-EC709iP/EC909iP MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C839 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50V C873 1-162-923-11 CERAMIC CHIP 47PF (EC909iP) (EC909iP) C840 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50V (EC909iP) C874 1-162-923-11 CERAMIC CHIP 47PF...
  • Page 45 HCD-EC709iP/EC909iP MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark JR607 1-216-864-11 SHORT CHIP R616 1-216-817-11 METAL CHIP 1/10W JR608 1-216-864-11 SHORT CHIP R621 1-218-887-11 METAL CHIP 0.5% 1/10W R622 1-218-887-11 METAL CHIP 0.5% 1/10W JR609...
  • Page 46 HCD-EC709iP/EC909iP MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R706 1-216-841-11 METAL CHIP 1/10W R707 1-216-817-11 METAL CHIP 1/10W R761 1-216-845-11 METAL CHIP 100K 1/10W R762 1-216-845-11 METAL CHIP 100K 1/10W R708 1-216-817-11 METAL CHIP...
  • Page 47 HCD-EC709iP/EC909iP MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R821 1-216-809-11 METAL CHIP 1/10W R856 1-216-825-11 METAL CHIP 2.2K 1/10W (EC909iP) (EC909iP) R822 1-216-809-11 METAL CHIP 1/10W R857 1-216-817-11 METAL CHIP 1/10W (EC909iP) (EC909iP) R858...
  • Page 48 HCD-EC709iP/EC909iP PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1749-021-A PANEL BOARD, COMPLETE (EC909iP: US, CND) < IC > A-1749-022-A PANEL BOARD, COMPLETE (EC909iP: AUS) A-1749-023-A PANEL BOARD, COMPLETE (EC709iP: US, CND) IC301 A-1772-963-B IC MB90F830PF-GE1 (for SERVICE)
  • Page 49 HCD-EC709iP/EC909iP PANEL POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R337 1-216-822-11 METAL CHIP 1.2K 1/10W < SWITCH > R340 1-216-833-11 METAL CHIP 1/10W R341 1-216-797-11 METAL CHIP 1/10W S301 1-762-875-21 SWITCH, KEYBOARD (I/1) (EC909iP)
  • Page 50 HCD-EC709iP/EC909iP POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C163 1-162-919-11 CERAMIC CHIP 22PF < RESISTOR > C164 1-162-923-11 CERAMIC CHIP 47PF R051 1-216-837-11 METAL CHIP 1/10W < CONNECTOR > R052 1-216-837-11 METAL CHIP 1/10W...
  • Page 51 HCD-EC709iP/EC909iP POWER Ref. No. Part No. Description Remark R153 1-216-851-11 METAL CHIP 330K 1/10W R154 1-216-841-11 METAL CHIP 1/10W R155 1-216-833-11 METAL CHIP 1/10W R156 1-216-845-11 METAL CHIP 100K 1/10W R157 1-216-817-11 METAL CHIP 1/10W R158 1-216-827-11 METAL CHIP 3.3K...
  • Page 52 HCD-EC709iP/EC909iP REVISION HISTORY Checking the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2010.03...

This manual is also suitable for:

Hcd-ec909ip

Table of Contents