Related Manuals for LEGRAND HX3 IS
Summary of Contents for LEGRAND HX3 IS
- Page 1 MAINTENANCE, INSTALLATION AND COMMISSIONING OF HX³/VX³ IS ENCLOSURES THE GLOBAL SPECIALIST IN ELECTRICAL AND DIGITAL BUILDING INFRASTRUCTURES...
- Page 2 Legrand reserves commissioning of Legrand low-voltage panel, in the right to change the specifications and illustrations without notice. All illustrations, accordance with directives 2006/95/EC, 2004/108/EC, and descriptions technical information included in this document are provided...
-
Page 3: Table Of Contents
SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . 23 WWW.LEGRAND.COM... -
Page 4: Introduction
Community Directives 2006/95/EC, 2004/108/EC, and the requirements of Standards EN 61439-1 (chapter 6.2.2.) and IEC EN 61439-2. Legrand assumes no responsibility for failure to comply with recommendations and instructions for any of the following events:... -
Page 5: Packaging And Protection
& PROTECTION BEFORE TRANSPORT DELIVERY Legrand advises you to protect the enclosures, and the equipment In order to reduce the weight for each column, we recommend that makes them up, with adequate packaging before delivery, to deliver the circuit breakers in plugged-in and draw-out... -
Page 6: Lifting/Handling
For the lifting of larger enclosures (XL³ 4000/6300), we recommend the use of Legrand lifting rings Cat.No 0 205 82. The installer/panel builder takes full responsibility for the use of any other means of handling (brackets, steel profiles, crossbars, etc.). - Page 7 Fig. 3A - Lifting the panels with cables Fig. 3B - Lifting the panels with cables and angle crossbars. (this assembly is to be done by the panel builder under his responsibility) MAINTENANCE, INSTALLATION & COMMISSIONING OF HX³/VX³ IS ENCLOSURES INSTALLATION GUIDE WWW.LEGRAND.COM...
- Page 8 LIFTING/HANDLING OF ENCLOSURES/PANELS: RINGS, ANGLE CROSSBARS, ETC . The operator carrying out the lifting operation must take into account all the necessary measures in order to carry out this operation in complete safety, and know all the following technical parameters: - Maximum Operating Load of the sling: maximum load that the sling can support in current use, - Slinging mode factor: factor applied to the maximum operating load of a single-strand sling to take into account the geometry of the slinging (number and angles of the strands) and the consequence of the folding of certain components.
-
Page 9: Acceptance
The absence of shock and the prohibition of tipping of the enclosures must also be clearly indicated on the packaging for the carrier. MAINTENANCE, INSTALLATION & COMMISSIONING OF HX³/VX³ IS ENCLOSURES INSTALLATION GUIDE WWW.LEGRAND.COM... -
Page 10: Delivery On Site
Fig. 2 - Panel shipped vertically on a pallet Legrand panels are normally delivered in transport units not exceeding 3 m in length, in standard packaging adapted to the transport and storage requirements. -
Page 11: Installation
For these connections it is necessary to follow the indications in the electrical diagram of the panel and the general diagram of the installation to be carried out. MAINTENANCE, INSTALLATION & COMMISSIONING OF HX³/VX³ IS ENCLOSURES INSTALLATION GUIDE WWW.LEGRAND.COM... - Page 12 INSTALLATION & IMPLEMENTATION (BY THE INSTALLER) It is imperative to indicate the electrical risks when opening the panels (e.g.: electrical hazard warning sticker). In the case of floor-mounted electrical enclosures, if the entry or outlet conductors pass through the lower part of the panel, it is necessary to use the guillotine openings provided for this purpose on the lower part of the panel (Fig.
- Page 13 ■ IP55 To obtain the IP55 degree of protection, it is essential to insert the sealing kit Cat.No 0 205 85 on the whole surface of the junction. Fig. 9 MAINTENANCE, INSTALLATION & COMMISSIONING OF HX³/VX³ IS ENCLOSURES INSTALLATION GUIDE WWW.LEGRAND.COM...
- Page 14 INSTALLATION & IMPLEMENTATION (BY THE INSTALLER) FIXING THE ENCLOSURE TO THE FLOOR For panels/enclosures to be fixed to the floor, the latter must be leveled and free of asperities (its inclination must be at most 1‰, both lengthwise and widthwise of the panel). Also check that the floor does not have any bumps that could create an imbalance of the panel or enclosure.
- Page 15 To obtain the actual dimensions of the base cladding, add 80 mm to dimensions A and B. Dimension B is also the drilling center distance for C-profiles (see previous page). FRONT FACE Position of the mounting holes for the XL³ 4000 enclosure bases MAINTENANCE, INSTALLATION & COMMISSIONING OF HX³/VX³ IS ENCLOSURES INSTALLATION GUIDE WWW.LEGRAND.COM...
-
Page 16: Connection, Wiring
CONNECTION, WIRING, ADD-ONS AND VARIOUS CONFIGURATIONS (different operators, under the installer’s responsability) • When you need to separate the main busbar, we advise you to make oblong holes to simplify the connection on site. If the columns are installed on a flat surface, the holes will be right in front each other. •... -
Page 17: Pre-Commissioning
In general, take into account the following indications: • Legrand faceplates are equipped with an automatic grounding system, using copper caps welded to the faceplates which, when the faceplates are tightened, guarantee equipotentiality with the frame by pressure, •... - Page 18 PRE-COMMISSIONING OPERATIONS (under the installer’s responsability) Replace the side panels, faceplates, etc., to make the panel ready for use. When carrying out this operation, take into account the following indications: • if the panels are provided with an equipotentiality cable with the structure (grounding), restore this connection using the original screw, •...
- Page 19 - Check the mechanical lock located on the back or side of the DPX³. - Check the metal lock located on the fixed part of the IS base - Check that the mechanical locks are tight MAINTENANCE, INSTALLATION & COMMISSIONING OF HX³/VX³ IS ENCLOSURES INSTALLATION GUIDE WWW.LEGRAND.COM...
- Page 20 PRE-COMMISSIONING OPERATIONS (under the installer’s responsability) SPECIFIC CHECKS ON THE OPERATION OF A DEVICE ON ITS IS BASE (FOR A DPX³ 630) First, disconnect the circuits downstream of the relevant IS base. Test purpose: to check the mechanical operation of the bases with their associated devices and to check the corresponding indications (position indicator for IS 333 bases).
-
Page 21: Recommended Screws And Tightening Torques
2000 0 373 59 50 Nm 4 046 09 (IS HD) 2000 0 373 59 50 Nm Suitable for hammer nuts supplied by Legrand ■ Flat bars SCREW SPECIFICATIONS AND RECOMMENDED TIGHTENING TORQUES I (A) Bar width Mini number Tightening... -
Page 22: Maintenance Register
3- Date of commissioning 4- Installing company 5- Maintenance company 6- Phone number for any need The instructions in this document refer to Legrand XL³ range panels/enclosures. If another type of structure is used, the same general concepts of this document remain valid. -
Page 23: Spare Parts
Base kit IS223 for DPX³ 250 3P 9 815 73 Base kit IS223 for DPX³ 250 4P 9 815 74 Base kit IS223 for DPX³ 160 3P without RCD MAINTENANCE, INSTALLATION & COMMISSIONING OF HX³/VX³ IS ENCLOSURES INSTALLATION GUIDE WWW.LEGRAND.COM... - Page 24 CAT.NO EQUIPMENT AND ACCESSORIES FOR ENCLOSURES 9 815 75 Base kit IS223 for DPX³ 160 3P without RCD 9 815 76 Base kit IS223 for DPX³ 160 4P with/without RCD 9 815 77 Base kit IS223 for DPX³ 160 4P with/without RCD 9 815 78 Base kit IS223 for DPX³...
- Page 25 Notes MAINTENANCE, INSTALLATION & COMMISSIONING OF HX³/VX³ IS ENCLOSURES INSTALLATION GUIDE WWW.LEGRAND.COM...
- Page 26 Notes...
- Page 27 Notes MAINTENANCE, INSTALLATION & COMMISSIONING OF HX³/VX³ IS ENCLOSURES INSTALLATION GUIDE WWW.LEGRAND.COM...
- Page 28 SUIVEZ-NOUS AUSSI SUR FOLLOW US ALSO ON legrand.com youtube.com/user/legrand facebook.com/Legrand twitter.com/Legrand pinterest.com/legrandgroup instagram.com/legrandnews Head office and International Department 87045 Limoges Cedex - France Tel: + 33 (0) 5 55 06 87 87 Fax: + 33 (0) 5 55 06 74 55...