Kärcher RCV 3 Manual page 21

c Remove the 2-in-1 dust container with water res-
ervoir.
3. Refill water.
Illustration M
a Pull up the rubber tab.
b Fill with water.
c Press the rubber tab down.
4. Install the 2-in-1 dust container with water reservoir.
Illustration F
a Press the 2-in-1 dust container with water reser-
voir into position until it audibly latches into place.
b Close the cover at the top.
5. Press the On/Off button.
Cleaning continues.
Emptying the 2-in-1 dust container with water
reservoir
1. Press any button.
The cleaning robot stops.
2. Remove the 2-in-1 dust container with water reser-
voir.
Illustration G
a Open the cover at the top.
b Press the clamp.
c Remove the 2-in-1 dust container with water res-
ervoir.
3. Empty the 2-in-1 dust container with water reservoir.
Illustration N
a Open the filter flap.
b Remove the filter flap.
c Empty the 2-in-1 dust container with water reser-
voir.
d Fit the filter flap.
e Close the filter flap.
4. Install the 2-in-1 dust container with water reservoir.
Illustration F
a Press the 2-in-1 dust container with water reser-
voir into position until it audibly latches into place.
b Close the cover at the top.
5. Press the On/Off button.
Cleaning continues.
Emptying the dust container
1. Press any button.
The cleaning robot stops.
2. Remove the dust container.
Illustration L
a Open the cover at the top.
b Press the clamp.
c Remove the dust container.
3. Empty the dust container.
Illustration O
a Fold the flap down.
b Empty the dust container.
c Fold the flap upwards until it audibly latches into
place.
4. Install the dust container.
Illustration K
a Press the dust container into position until it audi-
bly latches into place.
b Close the cover at the top.
5. Press the On/Off button.
Cleaning continues.
Cleaning the wiper cloth
The wiper cloth can be cleaned during a cleaning pro-
cess.
1. Press any button.
The cleaning robot stops.
2. Remove the wiper cloth holder.
Illustration J
a Press the clamps together.
b Remove the wiper cloth holder.
c Pull the wiper cloth off the wiper cloth holder.
3. Clean the wiper cloth.
4. Install the wiper cloth, see chapter Installing the
wiper cloth holder with wiper cloth.
5. Press the On/Off button.
Cleaning continues.
Where possible, always transport or return the device in
the original packaging. Please contact our Service De-
partment if the original packaging is not available.
Safety instructions for transporting
The lithium-ion battery is subject to the requirements of
dangerous goods regulations.
An undamaged and functional battery pack can be
transported by the user in public traffic areas without
any further restrictions.
When shipping by third parties (transport companies),
special requirements for packaging and labelling must
be observed.
Observe the national regulations.
ATTENTION
Damage to the cleaning robot due to incorrect stor-
age
Do not store the cleaning robot upside down. The hous-
ing of the laser radar (LiDAR) should never come into
contact with the ground or objects.
Do not place any objects on the cleaning robot.
Store the cleaning robot fully charged and switched off
in a cool and dry place.
Note
To avoid a deep discharge of the battery, fully recharge
the cleaning robot after 5 months at the latest.
1. Clean the cleaning robot, see chapter Cleaning.
2. Fully charge the cleaning robot, see chapter Manu-
ally sending the cleaning robot for recharging.
3. Unplug the charger from the mains socket and the
station.
4. Switch off the cleaning robot, see chapter Switching
off the cleaning robot.
5. Store the cleaning robot in a cool and dry place.
Care and service
Cleaning the 2-in-1 dust container
1. Press any button.
The cleaning robot stops.
2. Remove the 2-in-1 dust container.
Illustration G
a Open the cover at the top.
b Press the clamp.
c Remove the 2-in-1 dust container.
3. Clean the 2-in-1 dust container with water reservoir.
Illustration P
a Open the filter flap.
b Remove the filter flap.
c Empty the 2-in-1 dust container with water reser-
voir.
English
transport
Storage
Cleaning
21