Table of Contents ———————————————————— System Introduction ................1 General Features ......................1 Special Features ......................1 Postal Service Lock ....................1 Door Timer Cut-Off (Tailgate Prevention) ............1 Fire Alarm (Emergency) Input ................1 Multiple Entrances ....................1 Night Service ......................1 Wiegand Data Output ...................
System Introduction ——————————————————— General Features Tek-ENTRY ® Telephone Entry Systems are designed for easy operation and accommodate 1–750 suites. The no-phone-line system has many sophisticated features built in, such as:: • No monthly rental bill for telephone line. • Call waiting with distinctive double tone. •...
System Introduction Wiegand Data Output ® This feature connects Tek-Entry to a card access system with a Wiegand 26-bit input. When a tenant approves a visitor, the tenant’s code is sent to the card access system, causing the door to open. Guard Telephone The guard telephone must be a standard touchtone (DTMF) phone, and is connected directly to the PM900 Control Unit via two conductors.
System Installation and Programming –—————————— Installation Tips 1. Make arrangements with the telephone company to install CA71A or equivalent telephone blocks (one block for every 12 tenant phone lines). ® 2. Three 16 volt/40 VA UL Listed and CSA approved Class 2 power transformers are required—one for the lobby equipment, one for the electrical room equipment, and one for the door strike.
System Installation and Programming terminals “FA” and “G” to pulse open the entry door during a fire or other emergency. 7. Terminal “ME” is the interconnect point for multiple entrance systems. Interconnect terminals “ME” and “G” of all entry systems. Each location must also be wired with its own transformer, door strike, switch contacts, etc., as shown on Figure 1—System Wiring Diagram.
System Installation and Programming ® ® Complete the Tek-ENTRY Programming Worksheet, and ensure that it, the Tek-ENTRY Directory Worksheets and the User Operating Instructions are given to building management when installation and programming are complete. Program Mode—Begin/End Enter “*” and the three-digit master code (default is *123) to begin a programming session. Use the “1”...
System Installation and Programming View Keyless Entry Codes This section allows the review and/or deletion of keyless entry codes. 1. When the programming menu displays “VIEW KEYLESS CODES,” press the “#” key. The message “CODE TO REVIEW _____” will appear. 2.
System Installation and Programming Off-Premises Dialing Up to five off-premises telephone numbers can be assigned dial codes, if a telephone line is connected to the PM900 Control Unit. The telephone numbers are programmed in 11- digit format—enter asterisks “*” for unused leading digits, as follows: * (***) 555-5555 for 7-digit local calls * (555) 555-5555...
System Installation and Programming Notice to U.S. Installers and Users Incidence of Harm Should terminal equipment or protective circuitry cause harm to the telephone network, the telephone company shall, where practical, notify the customer that temporary discontinuance of service may be required; however, where prior notices are not practical, the telephone company may temporarily discontinue service if such action is deemed reasonable in the circumstances.
System Installation and Programming which can be determined by turning off the equipment to see if the interference stops— the user is encouraged to try and correct the interference by one or more of the following measures: 1. Reorient the receiving antenna. ®...
® Tek-ENTRY Programming Worksheet ——————————– Building Address: ___________________________________________________________________________ ___________________________________________________________________________ Date of Installation: ___________________________________________________________________________ Installation Company: ___________________________________________________________________________ ___________________________________________________________________________ Programming Instructions: A. Enter “*” and the three-digit Master Code (see #3 below) on the keypad to access the programming menu. B. Press the “1” key to scroll up, or press the “3” key to scroll down the menu screen to the desired function. C.
® Tek-ENTRY Telephone Entry System Operating Instructions A TekTone ® Tek-ENTRY ® Telephone Entry System has been installed in your building to provide increased security for yourself and your family. The system provides communication and entry control using your telephone. Your visitor will find your name and assigned dial code number on the directory near the Tek- ®...