Specific Safety Rules - Makita HR3200C Instruction Manual

Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Wear ear protection
Vibration
The vibration total
determined according to EN60745-2-6:
Work mode : chiseling function
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : hammer drilling into concrete, 16 mm
diameter and 100 mm depth
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : drilling into metal
Vibration emission (a
For Model HR3210FCT
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745-2-6:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Wear ear protection
Vibration
The vibration total
determined according to EN60745-2-6:
Work mode : chiseling function
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : hammer drilling into concrete, 16 mm
diameter and 100 mm depth
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : drilling into metal
Vibration emission (a
EC-DECLARATION OF CONFORMITY
Model; HR3200C,HR3210C,HR3210FCT
We declare under our sole responsibility that this
product is in compliance with the following standards of
standardized documents;
EN60745, EN55014, EN61000 in accordance with
Council Directives, 2004/108/EC, 98/37/EC.
000230
Tomoyasu Kato
) : 89 dB(A)
pA
) : 100 dB(A)
WA
value (tri-axial vector
2
) : 7.5 m/s
h,CHeq
2
2
) : 10 m/s
h,HD
2
2
) : 2.5 m/s or less
h,D
) : 88 dB(A)
pA
) : 99 dB(A)
WA
value (tri-axial vector
2
) : 8 m/s
h,CHeq
2
2
) : 10 m/s
h,HD
2
2
) : 2.5 m/s or less
h,D
CE2007
Director
Responsible Manufacturer:
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN
Authorized Representative in Europe:
ENG215-1
Makita International Europe Ltd.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
sum)
8JD, ENGLAND

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
ENG303-1
(gained from repeated use) replace strict adherence
to rotary hammer safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious
personal injury.
1. Wear ear protectors. Exposure to noise can
ENG302-1
cause hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tools by insulated gripping
surfaces when performing an operation where
the cutting tool may contact hidden wiring or
ENG102-1
its own cord. Contact with a "live" wire will make
exposed metal parts of the tool "live" and shock
the operator.
4. Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun
glasses are NOT safety glasses. It is also
highly recommended that you wear a dust
mask and thickly padded gloves.
ENG215-1
5. Be sure the bit is secured in place before
operation.
sum)
6. Under normal operation, the tool is designed
to produce vibration. The screws can come
loose easily, causing a breakdown or accident.
Check tightness of screws carefully before
operation.
ENG303-1
7. In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.
ENG302-1
8. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
ENH101-8
high locations.
9. Hold the tool firmly with both hands.
10. Keep hands away from moving parts.
11. Do not leave the tool running. Operate the tool
only when hand-held.
12. Do not point the tool at any one in the area
when operating. The bit could fly out and
injure someone seriously.
13. Do not touch the bit or parts close to the bit
immediately after operation; they may be
extremely hot and could burn your skin.
14. Some material contains chemicals which may
be toxic. Take caution to prevent dust
inhalation and skin contact. Follow material
5
GEB007-2