Table of Contents
Advertisement
Quick Links
INSTALLATION, OPERATION & MAINTENANCE MANUAL
Single Phase
115V, 60Hz
220V, 50Hz
Read this manual carefully before installing, operating, or servicing these pump models.
Observe all safety information. Failure to comply with instructions may result in
personal injury and/or property damage. Please retain these instructions.
PERFECTA Pump
Electric Submersible Pumps
GF32, IGF32 & TIGF32 Pump Models
1
®
®
Three Phase
230V, 60Hz
460V, 60Hz
415V, 50Hz
440V, 50Hz
460V, 50Hz
6/24/2021
Version
Advertisement
Table of Contents
Related Manuals for BJM Pumps PERFECTA Pump GF32
Summary of Contents for BJM Pumps PERFECTA Pump GF32
- Page 1 ® INSTALLATION, OPERATION & MAINTENANCE MANUAL ® PERFECTA Pump Electric Submersible Pumps GF32, IGF32 & TIGF32 Pump Models Single Phase Three Phase 115V, 60Hz 230V, 60Hz 220V, 50Hz 460V, 60Hz 415V, 50Hz 440V, 50Hz 460V, 50Hz Read this manual carefully before installing, operating, or servicing these pump models. Observe all safety information.
-
Page 2: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ................................3 SAFETY ..................................4 INSPECTION................................. 5 PRE-INSTALLATION INSPECTION ......................... 5 OIL FILL QUANTITY/TYPE ............................5 PUMP INSTALLATION ..............................6 INTENDED METHODS OF WIRING CONNECTION ....................6 SINGLE PHASE WIRING INSTRUCTIONS ......................6 THREE PHASE WIRING INSTRUCTIONS ......................6 SUMP, PIPING AND POWERING……………………………………………………………………………………………7 PUMP ROTATION .............................. -
Page 3: Introduction
This Installation, Operation and Maintenance manual provides important information on safety and the proper inspection, installation, operation, maintenance, and primary testing of the BJM Pumps® PERFECTA Series Submersible Pumps. This manual also contains information to optimize performance and longevity of your BJM Pumps® PERFECTA Series Submersible Pumps. -
Page 4: Safety
SAFETY Pump installations are seldom identical. Each installation and application can vary due to many different factors. It is the owner/service mechanics responsibility to install, operate, repair, service, and test to ensure that the pump integrity is not compromised according to this manual. Risk of electric shock –... -
Page 5: Inspection
4) Check for and tighten any hardware that appears loose. 5) Carefully read all tags, decals, and markings on the pump. If anything appears to be abnormal, contact your BJM Pumps distributor or Industrial Flow Solutions Operating, LLC. If damaged, the pump may need to be repaired before use. -
Page 6: Pump Installation
PUMP INSTALLATION PERFECTA Series Submersible Pumps have been evaluated for use with various fluid applications. Please contact the manufacturer for additional information. Risk of Electric Shock. Single Phase Pump models for 115V, 60Hz are supplied with a cable having grounding conductor and grounding-type attachment plug. -
Page 7: Sump, Piping And Powering
Installation and checking of electrical circuits and hardware should be performed by a qualified licensed electrician. Follow the instructions provided with the Control Panel to wire the system. SUMP, PIPING AND POWERING- Refer PERFECTA Pump Installation Diagram B • The pump can be installed in a sump or into a small pit in the sump. The small pit should be well-leveled and having total volumetric size approximately double than that of the pump. -
Page 8: Pump Operation
PUMP OPERATION This pump is designed to handle different type of liquids excluding volatile or flammable liquids. Do not attempt to pump any such liquid which may damage the pump or endanger personnel because of pump failure. Do not operate this pump where explosive vapors or flammable materials exist. -
Page 9: Trouble Shooting
Table 1. PERFECTA Three Phase Pump Operation with Control Panel Single Phasing Float Switch Pump Operation Control Panel Breaker Preventor (SPP) Position 1 *Manual Mode To START Press ON/Green Push Button Down Will STOP Will remain energized To START Press ON/Green Push Button TO STOP Press OFF/RED Push Button AUTO Mode... -
Page 10: Pump Is Heating Up
Pump must be disconnected from the electric power supply before proceeding to do any service or maintenance. To service or repair your pump, please contact your local BJM Pumps® distributor. Service should only be performed by a qualified electrician. Tools Needed... -
Page 11: Important Notes On Re-Assembly Of Pump
Important notes on re-assembly of Pump ▪ All O-rings should be lubricated with a Silicone based grease, or lubricated with same oil as in motor, before assembly. ▪ Replace Ball Bearings to shaft. ▪ To re-install Motor Housing Cover, lubricate bearing holder. Use a plastic or rubber mallet to lightly tap until cover is in place. -
Page 12: Warranty And Limitation Of Liability
Industrial Flow Solutions Operating, LLC 104 John W Murphy Drive New Haven, CT 06513, USA WARRANTY AND LIMITATION OF LIABILITY Industrial Flow Solutions Operating, LLC warrants each new pump against defects in workmanship and material for the period of 90 DAYS. It will replace or repair for the original purchaser, any genuine parts found to be defective upon return to its factory at CT (or other place as designated by it), transportation prepaid by purchaser. -
Page 16: Perfecta Three Phase Pump Installation In Sump, Diagram: B
PERFECTA Three Phase Pump Installation In Sump Diagram: B ONTROL PANEL PIPE ..- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ . J I ��;... - Page 19 19(1)
- Page 20 19(2)
- Page 21 19(3)
-
Page 22: Perfecta Pump Kick Back Motion, Image: E
PERFECTA Pump Kick Back Motion Image: E Kick Back Motion... -
Page 24: Perfecta Pump Exploded View, Diagram: G
PERFECTA Pump Exploded View, Diagram : G... - Page 25 PERFECTA Pump-0.4HP, 2 Pole Parts List Pos. No. Part Name Pos. No. Part Name Cable Grommet ( for Float Cable) Pump Handle Screw 4.2X22 Cable Entry (for Float Cable) Pump Top Cover Float Switch O-ring 105X5 Cable Clamp (In side Top Cover) Screw 4X6 Screw 2.9X9.5 Relay, Pump Protection...
-
Page 29: Perfecta Pump Dimensions With Float Switch, Diagram: J
PERFECTA Pump Dimensions with Float Switch Diagram : J... -
Page 30: Perfecta Pump Dimensions Without Float Switch, Diagram: K
PERFECTA Pump Dimensions without Float Switch Diagram : K... -
Page 31: Perfecta Pump Three Phase Control Panel Dimensions, Diagram: L
PERFECTA Pump Three Phase Control Panel Dimensions Diagram : L 10.75" 4.80" 2.91"...
Need help?
Do you have a question about the PERFECTA Pump GF32 and is the answer not in the manual?
Questions and answers