Safety Decals - Echo BEARCAT sc3206 Owner's Manual

1.9 saFETY dEcaLs

See Section 1.8 for decal locations. Familiarize yourself with all of the safety and operating decals on the machine
and the associated hazards. See the engine owner's manual or contact the engine manufacturer for engine safety
instructions and decals. Make certain that all safety and operational decals on this machine are kept clean and in good
condition. Decals that need replacement must be applied to their original locations.
1
p/N 12174
DO NOT OPERATE
WITHOuT SHIElDS IN
FAIluRE TO DO SO MAy CAuSE
SERIOuS INJuRy OR DEATH.
2
p/N 12175
KEEP HANDS AND FEET
OuT OF INlET AND
DISCHARgE OPENINgS
WHIlE MACHINE IS
OPERATINg TO AVOID
SERIOuS PERSONAl
INJuRy. STOP AND AllOW MACHINE TO COME TO A
COMPlETE STOP BEFORE ClEARINg OBSTRuCTIONS.
3
p/N 12176
DO NOT INSERT
BRANCHES lARgER
THAN 3/4 INCH INTO
SHREDDER OR MACHINE
DAMAgE MAy OCCuR.
4
p/N 12250
CHECK BlADE BOlTS
FOR PROPER TORQuE
AFTER EVERy 8 HOuRS
OF OPERATION. CHECK
BlADES AND ROTATE OR
RESHARPEN DAIly OR AS REQuIRED TO KEEP BlADES
SHARP. REFER TO OWNERS MANuAl FOR INSTRuCTIONS.
FAIluRE TO DO SO MAy CAuSE POOR PERFORMANCE,
DAMAgE OR PERSONAl INJuRy AND WIll VOID THE
MACHINE WARRANTY.
5
p/N 14703-00
lOWER lEVER SlOWly TO
ENgAgE CHIPPER. Pull lEVER
uP TO DISENgAgE CHIPPER.
CHIPPER/SHREDDER ROTOR
WIll CONTINuE TO ROTATE
WHEN CluTCH IS DISENgAgED.
REMOVE SPARK Plug WIRE BEFORE ClEANINg DEBRIS
FROM DISCHARgE AREA OR SERVICINg THIS MACHINE.
DO NOT OPERATE WITHOuT DISCHARgE SCREEN, INlET
FlAPS AND All SHIElDS IN PlACE.
MACHINE
PlACE.
STOP ENgINE AND
3 INCH CHIPPER/SHREDDER
6
p/N 14938-00
DO NOT INSERT BRANCHES
lARgER THAN 3 INCHES IN
DIAMETER INTO CHIPPER.
MACHINE DAMAgE MAy
OCCuR. REFER TO OWNERS MANuAl FOR OPERATINg
INSTRuCTIONS AND RECOMMENDATIONS.
7
p/N 14942-00
8
p/N 14965-00
DO NOT OPERATE THIS
EQuIPMENT IN THE
VICINITY OF BYSTANDERS.
DO NOT AllOW CHIlDREN
TO OPERATE THIS
EQuIPMENT.
OBTAIN AND WEAR
SAFETy glASSES
AND uSE HEARINg
PROTECTION AT All
TIMES WHEN OPERATINg
THIS MACHINE.
BEFORE INSPECTINg OR
SERVICINg ANy PART
OF THIS MACHINE, SHuT
OFF POWER SOuRCE,
DISCONNECT SPARK
Plug WIRE FROM SPARK
Plug AND MAKE SuRE
All MOVINg PARTS HAVE
COME TO A COMPlETE STOP.
AlWAyS STAND ClEAR OF DISCHARgE AREA WHEN
OPERATINg THIS MACHINE. KEEP FACE AND BODy AWAy
FROM FEED AND DISCHARgE OPENINgS.
WHEN FEEDINg SHREDDABlE MATERIAl INTO CHIPPER,
DO NOT AllOW METAl, ROCKS, BOTTlES, CANS OR ANy
OTHER FOREIgN MATERIAl TO BE FED INTO CHIPPER OR
SHREDDER.
BEFORE INSPECTINg OR SERVICINg ANy PART OF THIS
MACHINE, SHuT OFF POWER SOuRCE, DISCONNECT
SPARK Plug WIRE FROM SPARK Plug AND MAKE SuRE
All MOVINg PARTS HAVE COME TO A COMPlETE STOP.
SAFETY
5