Table of Contents
Advertisement
1.9 sAfETY DEcALs
See Section 1.10 for decal locations. Familiarize yourself with all of the safety and operating decals on the machine and the associ-
ated hazards. See the engine owners manual or contact the engine manufacturer for engine safety instructions and decals. Make
certain that all safety and operational decals on this machine are kept clean and in good condition. The decals are shown below at
reduced sizes. Refer to the parts catalog if you need a replacement decal. Decals that need replacement must be applied to their
original locations.
1
PN 12169
kEEP hANDS AND FEET OuT OF INLET AND
DISChARGE OPENINGS WhILE MAChINE IS OPERAT-
ING TO AvOID SERIOuS PERSONAL INjuRY. STOP
AND ALLOW MAChINE TO COME TO A COMPLETE
STOP BEFORE CLEARING OBSTRuCTIONS.
2
PN 12172
READ AND uNDERSTAND ThIS OWN-
ER/OPERATORS MANuAL. BE COM-
PLETELY FAMILIAR WITh ThE CON-
TROLS AND ThE PROPER uSE OF
ThIS EquIPMENT
OBTAIN AND WEAR SAFETY GLASS-
ES AND uSE hEARING PROTECTION
AT ALL TIMES WhEN OPERATING
ThIS MAChINE.
BEFORE INSPECTING OR SERvICING
ANY PART OF ThIS MAChINE, ShuT
OFF POWER SOuRCE, DISCONNECT
SPARk PLuG WIRE FROM SPARk
PLuG AND MAkE SuRE ALL MOvING
PARTS hAvE COME TO A COMPLETE
STOP.
3
PN 12173
DO NOT OPERATE ThIS EquIPMENT
IN ThE vICINITY OF BYSTANDERS.
DO NOT ALLOW ChILDREN TO OP-
ERATE ThIS EquIPMENT.
ALWAYS
STAND CLEAR OF DISChARGE AREA
WhEN OPERATING ThIS MAChINE.
kEEP FACE AND BODY AWAY FROM
DISChARGE AREAS.
4
PN 12174
DO NOT OPERATE MAChINE WIThOuT ShIELDS IN
PLACE. FAILuRE TO DO SO MAY CAuSE SERIOuS
INjuRY OR DEATh.
PN 18280-00 R041306
5
PN 12175
kEEP hANDS AND FEET OuT OF
INLET AND DISChARGE OPENINGS
WhILE MAChINE IS OPERATING
TO AvOID SERIOuS PERSONAL IN-
juRY. STOP AND ALLOW MAChINE
TO COME TO A COMPLETE STOP
BEFORE
CLEARING
OBSTRuC-
TIONS.
6
PN 12250
ChECk BLADE BOLTS FOR PROP-
ER TORquE AFTER EvERY 8
hOuRS OF OPERATION.
ChECk
BLADES AND ROTATE OR RE-
ShARPEN DAILY OR AS REquIRED
TO kEEP BLADES ShARP.
RE-
FER TO OWNERS MANuAL FOR
INSTRuCTIONS. FAILuRE TO DO
SO MAY CAuSE POOR PERFOR-
MANCE, DAMAGE OR PERSONAL
INjuRY AND WILL vOID ThE MA-
ChINE WARRANTY.
7
PN 13711-00
READ AND uNDERSTAND ThIS
OWNER/OPERATORS MANuAL.
BE
COMPLETELY
FAMILIAR
WITh ThE CONTROLS AND ThE
PROPER uSE OF ThIS EquIP-
MENT.
8
PN 18606-00
DO NOT OPERATE ChIPPER
WIThOuT
TuRNTABLE
BASE
LOCkED IN PLACE. FAILuRE TO
DO SO MAY RESuLT IN DAMAGE
TO MAChINE AND/OR SERIOuS
BODILY INjuRY.
FOR
TRANSPORT,
RETuRN
ChIPPER TO TRANSPORT PO-
SITION, INSERT TRANSPORT
SAFETY PIN AND CLIP, AND SET
TuRNTABLE
BRAkE
hANDLE
TO LOCkED POSITION.
FAIL-
uRE TO DO SO MAY RESuLT IN
DAMAGE TO MAChINE AND/OR
SERIOuS BODILY INjuRY.
SAFETY
7
Advertisement
Table of Contents
