Tektronix TDS1000B Series User Manual
Digital storage oscilloscopes
Hide thumbs
Also See for TDS1000B Series:
- Operator's manual (316 pages) ,
- User manual (199 pages) ,
- Service manual (137 pages)
Related Manuals for Tektronix TDS1000B Series
Summary of Contents for Tektronix TDS1000B Series
- Page 1 TDS1000B and TDS2000B Series Digital Storage Oscilloscopes User Manual *P071181702* 071-1817-02...
- Page 3 TDS1000B and TDS2000B Series Digital Storage Oscilloscopes User Manual www.tektronix.com 071-1817-02...
- Page 4 Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material.
- Page 5 Tektronix, shipping charges prepaid and with a copy of proof of purchase by the original purchaser. Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Tektronix service center is located.
- Page 6 Tektronix, with shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.
- Page 7 Table of Contents General Safety Summary ..................Compliance Information ..................EMC Compliance.................... Safety Compliance.................... Environmental Considerations ................Preface ......................xiii Help System ....................Firmware Updates Through the Internet ..............Conventions ....................Getting Started ...................... General Features ....................Installation ...................... Functional Check ....................Probe Safety ....................
- Page 8 Table of Contents Capturing a Single-Shot Signal ................Measuring Propagation Delay ................Triggering on a Specific Pulse Width............... Triggering on a Video Signal ................Analyzing a Differential Communication Signal............Viewing Impedance Changes in a Network..............Math FFT ......................Setting Up the Time-Domain Waveform ..............Displaying the FFT Spectrum ................
- Page 9 Table of Contents Vertical Controls .................... Appendix A: Specifications ..................Oscilloscope Specifications................P2220 Probe Specifications................Appendix B: Accessories ..................Appendix C: Cleaning ..................General Care ....................Cleaning ..................... Appendix D: Default Setup..................Appendix E: Font Licenses ..................Index TDS1000B/2000B Series Oscilloscope User Manual...
- Page 10 General Safety Summary General Safety Summary Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it. To avoid potential hazards, use this product only as specified. Only qualified personnel should perform service procedures. To Avoid Fire or Personal Use Proper Power Cord.
- Page 11 General Safety Summary Do Not Operate in Wet/Damp Conditions. Do Not Operate in an Explosive Atmosphere. Keep Product Surfaces Clean and Dry. Provide Proper Ventilation. Refer to the manual’s installation instructions for details on installing the product so it has proper ventilation. TDS1000B/2000B Series Oscilloscope User Manual...
- Page 12 General Safety Summary Terms in this Manual These terms may appear in this manual: WARNING. Warning statements identify conditions or practices that could result in injury or loss of life. CAUTION. Caution statements identify conditions or practices that could result in damage to this product or other property.
- Page 13 IEC 61000-4-6:2003. Conducted RF immunity IEC 61000-4-11:2004. Voltage dips and interruptions immunity EN 61000-3-2:2006. AC power line harmonic emissions EN 61000-3-3:1995. Voltage changes, fluctuations, and flicker European Contact. Tektronix UK, Ltd. Western Peninsula Western Road Bracknell, RG12 1RF United Kingdom This product is intended for use in nonresidential areas only.
- Page 14 Compliance Information Ambient conducted fields may induce triggering when the trigger threshold is offset less than 1 major division from ground reference. The increase in trace noise while subjected to the test field (3 V rms over the frequency range of 150 kHz to 80 MHz, with 80% amplitude modulation at 1 kHz) is not to exceed 1 major division peak-to-peak.
- Page 15 Compliance Information Safety Compliance EC Declaration of Compliance was demonstrated to the following specification as listed in the Official Journal of the European Communities: Conformity – Low Voltage Low Voltage Directive 2006/95/EC. EN 61010-1: 2001. Safety requirements for electrical equipment for measurement control and laboratory use.
- Page 16 Compliance Information Installation (Overvoltage) Terminals on this product may have different installation (overvoltage) category designations. The installation categories are: Category Descriptions Measurement Category IV. For measurements performed at the source of low-voltage installation. Measurement Category III. For measurements performed in the building installation.
- Page 17 (WEEE) and batteries. For information about recycling options, check the Support/Service section of the Tektronix Web site (www.tektronix.com). Mercury Notification. This product uses an LCD backlight lamp that contains mercury. Disposal may be regulated due to environmental considerations. Please contact your local authorities or, within the United States, refer to the E-cycling Central Web page (www.eiae.org) for disposal or recycling information.
- Page 18 Compliance Information TDS1000B/2000B Series Oscilloscope User Manual...
- Page 19 Preface Preface This manual contains operating information for the TDS1000B and TDS2000B Series Digital Storage Oscilloscopes. The manual consists of the following chapters: The Getting Started chapter briefly describes features of the oscilloscope and provides installation instructions. The Operating Basics chapter covers operating principles of the oscilloscopes. The Understanding Oscilloscope Functions chapter describes basic operations and functions of an oscilloscope: setting up the oscilloscope, triggering, acquiring data, scaling and positioning waveforms, and taking measurements.
- Page 20 If a newer version of firmware becomes available, you can use the Internet and a USB flash drive to update your oscilloscope. If you do not have access to the Internet, contact Tektronix for information on update procedures. NOTE. The oscilloscope requires you to use a USB flash drive of 2 GB or less to update the firmware.