Advertisement
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. Three long chirps & Three parking light flashes
confirm exit.
B. ALARM FEATURES PROGRAMMING:
I
ALARM FEATURE "
1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
2. Push the Valet switch 2 times and holding in on 2
then release the valet switch. You are now in the Alarm feature 'I' programming mode.
3.
Press and release the transmitter button 'A' corresponding to the feature 'A' you want to change.
a. The siren chirps and LED pause will indicate new setting.
b. The system would advance to [2] LED flash, [2] chirp. (The factory default setting is always [1] LED flash,
[1] chirp.)
4
Depress the transmitter button 'A' again to change the feature again. Simply keep re-depressing the
transmitter button 'A' again until the module advances to your desired setting.
5. Depress the transmitter button 'B' corresponding to the feature 'B' you want to program.
Press
One Chirp /
Transmitter
LED one pulse
Button
Factory Default Setting
Chirps on
1
Automatic Rearm On
2
Instantly Door Ajar Warning.
3
+
Exit
: Turn Ignition to 'ON' position, or leave it for 15 seconds. Three long chirps to confirm exit.
II
ALARM FEATURE "
1
Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
2
Push the Valet switch 4 times and holding in on the 4
release the valet switch. You are now in the Alarm feature 'II' programming mode.
3
Press and release the transmitter button 'A' corresponding to the feature 'A' you want to program.
Press
One Chirp /
Transmitter
LED one pulse
Button
Factory Default Setting
0.9-second Door lock
1
pulses.
Active arming
2
Ignition controlled door locks
3
+
& unlocks
Exit
: Turn Ignition to 'ON' position, or leave it for 15 seconds. Three long chirps to confirm exit.
III
ALARM FEATURE "
1
Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
2
Push the Valet switch 6 times and holding in on the 6
then release the valet switch. You are now in the Alarm feature 'III' programming mode.
3
Press and release the transmitter button 'A' corresponding to the feature 'A' you want to program.
Press
One Chirp /
Transmitter
LED one pulse
Button
Factory Default Setting
1
Tan Wire = Trunk (Channel 3) Output
2
Car Jacking Off
3
+
Exit
: Turn Ignition to 'ON' position, or leave it for 15 seconds. Three long chirps to confirm exit.
ADJEST AND TEST THE SENSITIVITY LEVEL OF THE SHOCK SENSOR
1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
2. Push the Valet switch 6 times and holding in on the 6th push until three chirps with a long chirp is heard then
release the valet switch. You are now in the Alarm feature 'Shock Sensor' programming mode.
3. Press and hold
button for 2 seconds. One long siren chirp to indicate the unit is ready to accept
adjustments for the second stage of the shock sensor (full alarm).
4. Press
button on the transmitter once will decrease sensitivity level by one, each time an decrease is
made the siren chirp will respond with [1] chirp, while 2 chirp indicates the minimum of sensitivity.
5. Press
button on the transmitter once will increase sensitivity level by one, each time an increase is made
the siren/horn chirp will respond with [1] chirp, while 2 chirp indicates the maximum of sensitivity.
CA100
" PRORAMMING:
" PRORAMMING:
Two Chirps /
LED two pulse
3.0-second Door lock pulse.
Passive arming without
passive door locking
Without ignition controlled
door locks & unlocks
" PRORAMMING:
nd
push until one short chirp with one long chirp is heard
Two Chirps /
LED two pulse
Chirps off
Automatic Rearm Off
45 seconds Delay Door Ajar error chirp.
th
push until two chirps with a long chirp is heard then
th
push until three chirps with a long chirp is heard
Two Chirps /
LED two pulse
Shock Sensor Program Mode
Gray Wire = Two Step Door Unlock Output
Car Jacking On
2
05-04-06
Three Chirps /
LED three pulse
Double pulse unlock
Passive arming with passive
door locking.
Hide quick links:
Advertisement
