Advertisement
安装步骤
如何安装出水口
若因维修或其它原因拆下软管(1)，装
回时手动拧紧即可。
将固定螺杆(2)安装到水龙头(3)底部，
将装饰盖(4)穿过软管、固定螺杆和提
拉线缆(5)嵌入到水龙头底部。
将水龙头组件插入脸盆安装孔中，使
2
装饰盖接触台面。
从脸盆下方把垫片(6，橡胶垫片放在
8
上面)穿入固定螺杆，调整水龙头使出
水口朝前，用工具(7)锁紧螺母(8)以固
定水龙头。
1
把 软 管 接 到 冷 热 水 源 ， 冷 水 管 贴 有
"COLD"标签。
如何安装排水器
将止水塞(9)、法兰盘(10)及垫片(11)从
排水本体(13)取下。把排水本体组件从
脸盆下方插入排水孔中，调整至合适
的位置，再将法兰盘(10)带垫片(11)旋
到排水本体上。
用 扳 手 拧 紧 排 水 本 体 上 的 锁 紧 螺 母
(12)。把止水塞(9)放入排水组件。
13
注意：如果需要，可直接在法兰盘(10)
底面沿周围涂一圈密封油灰或其它密
封剂，而不使用垫片(11)。
打开排水本体上的盖板(14)，将提拉线
缆末端(15)嵌入拉线盒(16)内部的方孔
(17)中。使其在拉线盒两端(A, B)卡到
位，如图所示。
然后用手扣紧盖板(14)。装好后请拉动
提拉头(18)，确保其正常工作。
注意：在锁紧螺母拧紧后，如法兰盘
使用密封油灰或其它密封剂，则不可
以调整排水本体位置，否则会破坏油
灰密封的密封性。同时去除多余油灰 。
1483418-T2-A
INSTALLATION
How to Install the Faucet
If need to take off the hoses(1) to repair,
reinstall and tighten them by hand.
Install the mounting studs(2) into the
faucet(3) bottom. Slide the escutcheon(4)
over the hoses, mounting studs and cable
(5) until it is put into the faucet bottom.
3
4
Insert the faucet assembly into the hole
of the lavatory until the escutcheon
contacts the deck.
6
From underside of the lavatory, place the
8
washers(6, rubber washer is on the top)
5
onto the mounting studs. Position the
faucet．Tighten the nuts(8) with tool(7) to
secure the faucet.
7
Attach the hoses to water supplies.
The hose with "COLD" label should be
connected to cold water.
How to Install the Drain
9
Remove the stopper(9), flange(10) and
washer(11) from the drain body(13).
Insert the drain body through the drain
10
hole from underside, and adjust the
11
position properly. Screw the flange(10)
with washer(11) onto the drain body.
Tighten the locknut(12) on the drain body
12
with wrench. Insert the stopper(9) into the
drain assembly.
NOTE: If needed, apply a ring of
plumbers putty or other sealants around
the underside of the flange(10), instead
of using washer(11).
18
Open the coverplate(14) on the drain
body, and insert cable end(15) into the
16
square hole(17) of the cable box(16).
Make sure the cable is properly buckled
at both ends(A, B) of the cable box as the
15
14
figure shown.
Lock the coverplate(14), and verify the lift
rod(18) on the faucet is linked correctly
with the drain body through the cable.
B
NOTE: Do not reposition the drain if
A
plumbers putty or other sealants applied
after the locknut is tightened, or you may
17
break the putty seal. Wipe away excess
plumbers putty.
安装结果检查
检查并确保所有衔接螺母都已拧紧，
确保把手在关闭位置。
打开排水器和主要供水源，检查是否
有漏水。如有漏水，修理之。
先用六角扳手(19)取出螺钉(20)，再用
工具(21)拆下起泡器(22)。打开水龙头
冷热水，让水流出约一分钟以清除杂
质，检查渗漏。冲洗起泡器，关闭水
龙头，重新装回起泡器，锁紧螺钉。
清洗说明
适用于所有加工处理过的表面：以中性肥皂水清洗镀
层表面，再以干净的软布彻底擦干整个表面，许多清
洁剂，比如氨水、去污粉及洁厕灵等，会对电镀表面
造成伤害，切忌使用。
有磨损性的清洁用具或清洁剂也不可使用于科勒牌的
水龙头及其配件上。
2
1483418-T2-A
INSTALLATION CHECKOUT
Ensure all connections are tight.
Ensure the handle is in the off position.
Turn on the drain and main water supply,
and check for leaks. Repair as needed.
Uninstall the screw(20) with hex wrench
(19). Remove the aerator(22) with tool
20
(21). Turn on the faucet. Run hot and cold
22
water through the spout for about one
19
21
minute to remove any debris. Check for
leaks. Remove any debris from the
aerator. Shut off the faucet. Reinstall the
aerator. Tighten the screw.
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm
water. Wipe entire surface completely dry with clean
soft cloth. Many cleaners may contain chemicals, such
as ammonia, chlorine, toilet cleaner etc. which could
adversely affect the finish and are not recommended
for cleaning.
Do not use abrasive cleaners or solvents on Kohler
faucets and fittings.
3
Advertisement
