Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Delta CS-NT24
- Page 1 Multi-function Cable Tester User Manual...
- Page 2 • Thank you for purchasing the Cable Tester. Please read the manual before using the Cable Tester and use properly. • For using the Cable Tester safely, please first read the「Safety Information」carefully in the manual. • The manual should be kept well in case of reference. •...
-
Page 3: Table Of Contents
Content 1. Safety information ............................1 2. Production Introduction ..........................2 2.1 Feature ..............................2 2.2 Packing list ............................2 2.3 Interface and Function Introduction ...................... 3 3. Operation ..............................6 3.1 Installing the Battery ..........................6 3.2 Auto power off function ........................6 3.3 OSD Menu ............................ -
Page 4: Safety Information
1. Safety information ◆ The cable tester is intended to use in compliance with the local rules of the electrical usage and avoid to apply at the places which are inapplicable for the use of electrics such as hospital, gas station etc. ◆... -
Page 5: Production Introduction
2. Production Introduction 2.1 Feature 2.4 inch TFT-LCD screen, 320x240 resolution ● Secondary code digital mode, decisively rejects noise and false signals, locate cables quickly and easily. ● Advanced UTP cable test, test UTP cable's sequence, type and remote kit, quickly detect the near-end, mid-end ●... -
Page 6: Interface And Function Introduction
2.3 Interface and Function Introduction 1) Cable tester Interfaces : Telephone status indicator The charge indicator: It lights red while the battery is being charged. As the charging is complete, the indicator turns off automatically Upward, set or modify parameters Leftward, set or modify parameters Confirm key Rightward, set or modify parameters... - Page 7 Left Interface: Right Interface: Top Interface: RJ11 cable tracer and status test port UTP cable test, cable tracer and switch test port DC 5V 1A charging port Network cable test port (Ping/ Port flicker/ IP scan) RJ45 cable TDR/ Network link status test port TDR 2.0 test port (RJ45) TDR 2.0 test port(BNC) Video level meter port (CVBS/TVI/CVI/AHD)
- Page 8 2) Cable tracer (Receiver) Interfaces and functions： LED light Power Indicator UTP cable sequence / signal strength indicator Shielded layer continuity indicator Earphone jack UTP cable test port LED light switch 100M /1000M indicator Switch / Sensitivity knob MUTE button (long press to silent mode, short press to port connectivity detection) UTP cable type indicator: straight /cross /other Port continuity detection indicator (ON indicates local end cable connectivity function, OFF indicates cable sequence function)
-
Page 9: Operation
Bottom interface PD Powered test port (detect whether the power output of the PoE switch pins is normal.) Note: Receiver port continuity detection only supports the local end, does not support the remote end. Emitter can support the near end, middle end and far end port detection. 3. -
Page 10: Cable Tester
4. Cable tester 4.1 UTP cable test Connect the network cable into the cable tester’s RJ45 port, the BNC cable or RJ11 telephone line connect to the cable tester’s BNC or RJ11 port. If no connector cable, can use alligator clips to clip the bare copper wire. key to select the “SCAN UTP”... -
Page 11: Utp Cable Test
continuity of the line of the RJ45 cable connector or within 1 meter from RJ45 cable connector. As shown on the right, If the light is on, it means it is connected and vice versa. Connect the network cable into the cable tester’s RJ45 port, the other end of network cable disconnect any device. - Page 12 Can identify cable’s type through the “Direct/Cross/other” indicator. And also can identify the cable whether suitable 100M or Gigabit cable. Can display the remote number(Default is 255) The 1-8 indicators on the cable tracer will flash in sequence according to the network cable sequence, will display the cable type through the “Direct/Cross/other”...
-
Page 13: Short Circuit Detection
4.1.3 Short circuit detection The cable not connect wire receiver end: If connect cable short circuit, the short circuit line indicator will flash. In the left side of interface, the “√” means the RJ45 cable connector of cable tester and wire receiver is normal, the “x”... -
Page 14: Rj45 Cable Tdr Test
switch, also can detect the short circuit status of network cable. 4.2 RJ45 cable TDR test Connect network cable to cable tester's RJ45 port, press key to RJ45 TDR icon and enter the interface. Single test: Test cable status, length and attenuation. Repeat test: Continue to test cable status, length and attenuation. -
Page 15: Tdr 2.0 Test (Optional)
4.3 TDR 2.0 Test (Optional) Note: The testing cable can't be connected to any equipment, otherwise it will damage the tester. Connect Alligator clip cable to the TDR port, and the cable must connect well before testing, otherwise it will influence the accuracy. -
Page 16: Network Test
user-defined. Press key to adjust the cable speed, when the screen display length and real length are the same, please to select the cable type, press “Save” key to save the select the start, then press to confirm. Press the calibration data. -
Page 17: Ping
any changes on the LAN port. Application: The tester will send special signals to make the connected LAN port flicker at special frequency, which will enable the installers to easily and quickly find the connected Ethernet cable. This function can prevent mistakenly insertion or disconnection non-corresponding cable to artificially interrupt network connection. -
Page 18: Ip Search
5.3 IP search Connect a network cable to the meter's “PING/Port flashing” port, press key to “IP Scan” icon and enter to app interface. key to “Set IP” function, press Press to set the tester’s IP address, the tester’s IP address must be same network segment with the scanned network equipment, and select the “Scan”... -
Page 19: Other Functions
Press key to “level” icon and enter to app interface, the tester will auto start testing, the top of screen will display “Testing”, and auto display the peak level, sync level and burst level. Press key to switch the MV and IRE (Institute of Radio Engineers) mode, NTSC format uses IRE as the unit of measurement, and PAL format uses mV as the unit of measurement. -
Page 20: Pd Powered Detected
7.2 PD powered detected PoE switch or PSE power supply device connected to the “PD” port of the wire receiver, if the indicator light is on, it means PoE voltage output working normal. There are 2 indicators lights of the “PD” port, when testing the pins used of PoE switch for power supply, if 1236 indicator light is ON, it means PoE switch supply power through Pin 1236. -
Page 21: Specification
8. Specification Network tester & Cable tester Item series Display 2.4 inch TFT-LCD screen , 320x240 resolution UTP cable Test UTP cable's sequence, type and remote kit, quickly detect the near-end, test mid-end and far-end fault point of RJ45 cable connector Cable test Cable type...