Advertisement
Quick Links
D o o r Ac t iv a ti o n D e v i c e s
CM-221M
Touchless Exit Switch with Remote LED Triggering
INSTALLATION INSTRUCTIONS
PARTS INCLUDED IN THE BOX
• (1) CM-221M Touchless Exit Switch with Manual Override pushbutton
• (1) Parts bag (Contents: (2) 6-32 X 1/2" oval head Phillips ss screws, (2) 6-32 X 1/2" snake eye s/s flat head
screws, (1) Key for tamper proof screws (snake eye), (1) Jumper for factory external LED control)
• (1) User/Installation Manual
• (1) Faceplate Gasket
1. GENERAL DESCRIPTION
The CM-221M Hands-Free Switch uses active infra-red
microburst sensor technology, designed for use in ADA
compliant automatic door control applications and access
control.
The CM-221M switches eliminate the spread of germs by
avoiding physical contact, and provide greater convenience
when moving through the premises. The switches are available
with stainless steel faceplates, in narrow (jamb) or single gang.
All models are ROHS compliant with lead-free construction.
Built-in remote LED switching allows for integration with
third-party applications, such as guard and nurse station
annunciators. Adjustable time delay from 0.5 to 20 seconds
and an adjustable range from (2" to 8" / 5cm to 20cm).
2. SPECIFICATIONS
Voltage
Current
PIR Contact Rating
PIR Contacts
Temperature Range
Response Time
Pushbutton
Contact Rating
Pushbutton
Contacts
NOTE: Do NOT use AC Voltage for this unit.
Please see section 8 for power requirements
12 to 24 VDC +/- 10%
45 mA (peak)
1 Amp @ 30 VDC
Common/ N.O./ N.C.
14F to 122F (-10 to 50 °C)
10ms
1 Amp, 30 VDC
Common/N.O./N.C
Dimensions
3. FEATURES
•
Built-in Red and Green LED indication.
Factory default = Red (Standby), Green (Triggered)
•
Red and Green LEDs can be controlled by sensor or
externally
•
Adjustable detecting distance: 2 to 8 Inches (5 cm to 20 cm)
•
Adjustable Time Delay: 0.5 seconds to 20 seconds
•
Toggle function selection available
•
IP65 rating
•
IR lens to provide stable and reliable operation
4. OPERATION AT A GLANCE
In a typical application, as you approach the CM-221, the LED
will be red. When you wave your hand in front it will change
the LED to green, and trigger its relay to change state and
unlock your door, or trigger the door operator to open the
door. The toggle feature can be used to trigger the door to
remain in the unlocked position, until you wave your hand a
second time to relock it.
Narrow:
1 3/4" W x 4 1/2" H x 1 1/4" D
(43 mm x 114 mm x 31 mm)
Single Gang:
2 3/4" W x 4 1/2" H x 1 1/4" D
(70 mm x 114 mm x 31 mm)
Page 1 of 6
Advertisement
Related Manuals for CAMDEN ValueWave CM-221 Series
Summary of Contents for CAMDEN ValueWave CM-221 Series
- Page 1 D o o r Ac t iv a ti o n D e v i c e s CM-221M Touchless Exit Switch with Remote LED Triggering INSTALLATION INSTRUCTIONS PARTS INCLUDED IN THE BOX • (1) CM-221M Touchless Exit Switch with Manual Override pushbutton •...
- Page 2 CM-221M TOUCHLESS EXIT SWITCH I NS TA L L AT IO N I NST RUCT I ONS 5. CONFIGURING THE CM-221M Range of Detection and Output Duration Looking at the back of the CM-221M with the Mode pins located at the top, you will see two adjustment potentiometers. The one on the left can be turned clockwise to set the range of detection (2”...
- Page 3 CM-221M TOUCHLESS EXIT SWITCH INSTA LL AT ION INS T RUCT IONS 6. WIRING THE CM-221 1. Connection to a Maglock Connect the ground (-) of the maglock to the ground (-) of the VDC power supply. Next connect the (+) of the maglock to the (N.C.) of the manual pushbutton.
- Page 4 ‐ Jumper must be ON, 120 VAC shorting the two pins to enable remote selection of LED colors IR Sensor CM-221M TOUCHLESS EXIT SWITCH WITH REMOTE LED TRIGGERING I NS TA L L AT IO N I NST RUCT I ONS CX‐TR Transformer 12, 16 or 24 VAC Common N.O. CAUTION: All unused wire N.C. conductors should be individually isolated and taped. Manual Push 2. Connection to a Door Operator CX‐PS13 Power Supply 7 ...
- Page 5 CM-221M at any time. Note: A linear output VDC power supply is strongly recommended. If using power from other than Camden’s CX-PS13 filtered regulated power supply, you must measure the provided power before applying power to the CM-221M. Voltages of more than 10% over the specified acceptable range or using a power supply with large amounts of AC voltage on it (unfiltered unregulated power such as a transformer and a rectifier) may damage the CM-221M and void the warranty.
-
Page 6: Ordering Information For Replacement Parts
CM-221M TOUCHLESS EXIT SWITCH I NS TA L L AT IO N I NST RUCT I ONS ORDERING INFORMATION FOR REPLACEMENT PARTS ITEM NUMBER PART NUMBER DESCRIPTION 60-31A083 TOUCHLESS SENSOR SWITCH WITH EXTERNAL LED CONTROL 60-49B040-xxx NARROW STAINLESS-STEEL FACEPLATE 60-49H009L-xxx SINGLE GANG STAINLESS-STEEL FACEPLATE 60-59H000 GASKET FOR NARROW GANG TOUCHLESS SWITCH...