Table of Contents
Advertisement
Display Setup
1
Set the A-B-C Switch
The A-B-C switch is located inside
the battery compartment. It can
be set to A, B or C. However,
you must select the same letter
choices for both the sensor and
the display in order for the units
to synchronize.
2
Plug Power Adapter into
Electric Outlet
1
A-B-C Switch
Set to match
sensor
A B C
2
Plug in Power
Adapter
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE
WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to
be used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of
used batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries
in fire, as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT
recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.
3
Write Down the DEVICE ID
12 digit unique ID needed for
online connectivity functions.
24 C8 6E
4
Install or Replace Backup
Batteries (optional)
Insert 3 x AA alkaline batteries
into the battery compartment,
as shown. Follow the polarity
(+/-) diagram in the battery
compartment.
3
Write Down
DEVICE ID
4
Install Backup
12 digit number
Batteries
(optional)
3 AA Batteries
IMPORTANT: Batteries are a backup
power source to preserve records
in the event of a power outage.
Power adapter is the recommended
primary power source to enjoy the full
functionality of this product.
8
Set the Time, Date & Units
Press the " SE T " button, located on the front of the display, to enter SET
MODE. Once in set mode, the preference you are currently setting will blink on
the display.
To adjust the currently selected (flashing) item, press and release the "
"
" buttons (press and HOLD to fast adjust).
V
To save your adjustments, press and release the " S E T " button again to adjust
the next preference. The preference set order is as follows:
TOP DISPLAY:
CLOCK HOUR
CLOCK MINUTE
CALENDAR MONTH
CALENDAR DATE
CALENDAR YEAR
TEMPERATURE UNITS (ºF or ºC)
WIND SPEED UNITS (MPH, KPH, Knots)
RAINFALL UNITS (in or mm)
PRESSURE UNITS (inHg or hPa)
TICKER DISPLAY:
LANGUAGE (English or French)
WEATHER TICKER SPEED (SLOW, MEDIUM, FAST)
PC CONNECT MODE (1, 2, 3, 4)
You will automatically exit SET MODE if no buttons are pressed for 20 seconds.
Enter setup mode at any time by pressing the " S E T " button.
Display Backlight Settings
This weather station's color display features three different lighting settings:
High (100%) brightness, Medium (60%) brightness and Low (30%) brightness.
When display is powered with the power adapter, backlight remains on
at 100% brightness. Press the " " button once to dim to 60% brightness;
press again to dim to 30%, press a 3rd time to enter AUTO DIM mode.
"AUTO DIM" will appear below the clock.
AUTO DIM MODE:
Automatically adjusts display brightness based on time of day & year.
6:00 a.m. - 9:00 p.m. = 100% brightness
MARCH 11- NOVEMBER 4
9:01 p.m. - 5:59 a.m.= 30% brightness
NOVEMBER 5 - MARCH 10 7:30 a.m. - 7:00 p.m.= 100% brightness
7:01 p.m. - 7:29 a.m. = 30% brightness
T
" or
9
Advertisement
Table of Contents
