Chauvet DJ 4BAR Flex Q ILS User Manual
Hide thumbs Also See for 4BAR Flex Q ILS:

Advertisement

Quick Links

User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 4BAR Flex Q ILS and is the answer not in the manual?

Questions and answers

Summary of Contents for Chauvet DJ 4BAR Flex Q ILS

  • Page 1 User Manual...
  • Page 2: Table Of Contents

    Display Orientation..................... Firmware Version ....................IRC-6 Infrared Remote Control ..............Master/Slave Mode (Wired) ................Master/Slave Mode (D-Fi USB)..............ILS Mode....................... 5. Maintenance..................Product Maintenance ..................6. Technical Specifications..............Returns ....................Contact Us....................4BAR Flex Q ILS User Manual Rev. 1...
  • Page 3: Before You Begin

    Electronically published by Chauvet in the United States of America. Chauvet, Chauvet DJ, the Chauvet logo, and 4BAR Flex Q ILS are registered trademarks or trademarks of Chauvet & Sons LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other company and product names and logos referred to herein may be trademarks of their respective companies.
  • Page 4: Safety Notes

    Keep this User Manual for future use. If the product is sold to someone else, be sure that they also receive this document. Page 2 of 17 4BAR Flex Q ILS User Manual Rev. 1...
  • Page 5: Introduction

    Battery Cover RF DIP (9-Volt battery) Switch WARNING! DO NOT plug anything other than a D-Fi USB into the USB port. Doing so may cause damage to the product. 4BAR Flex Q ILS User Manual Rev. 1 Page 3 of 17...
  • Page 6: Product Dimensions

    Front View 45.7 in 1161 mm 43.3 in 1100 mm 12.8 in 326 mm 11.6 in 295 mm Side View 4.7 in 121 mm 3.7 in 95 mm Page 4 of 17 4BAR Flex Q ILS User Manual Rev. 1...
  • Page 7: Setup

    It is possible to power link up to 6 4BAR Flex Q ILS products on 120 VAC or up to 13 4BAR Flex Q ILS products on 230 VAC. The power linking diagram corresponds to the North American version of the product ONLY! If using the product in other markets, you must consult with the local Chauvet distributor as power linking connectors and requirements may differ in your country or region.
  • Page 8: Mounting

    Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The 4BAR Flex Q ILS may be mounted in any position; however, make sure adequate ventilation is provided around the product. Rigging • Before deciding on a location, always make sure there is easy access to the product for maintenance and programming.
  • Page 9: Operation

    Enable Master/Slave with other 4BAR Flex Q ILS products Enable Master/Slave with legacy 4BAR products DMX Linking The 4BAR Flex Q ILS works with a DMX controller. Information about DMX is in the CHAUVET DMX Primer, which is available from the Chauvet website http://www.chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf.
  • Page 10: Personality And Starting Address

    If the starting address is set too high, access to some of the product’s channels could be restricted. The 4BAR Flex Q ILS uses up to 19 DMX channels in a 19-Ch DMX mode, which defines the highest configurable address to 494.
  • Page 11: Dmx Channel Assignments And Values

    Amber 4 000  255 0–100% – – Dimmer 000  255 0–100% 000  009 No function – – Strobe 010  255 Strobe, slow to fast 4BAR Flex Q ILS User Manual Rev. 1 Page 9 of 17...
  • Page 12: Configuration (Standalone)

    DMX signals from the controller. Static Colors To run the 4BAR Flex Q ILS in Preset Color mode, follow the instructions below: 1. Press <MENU> repeatedly until C-- shows on the display. 2. Press <ENTER>.
  • Page 13 Press and hold Fade to blackout The 4BAR Flex Q ILS footswitch will work properly in any mode, with a maximum unobstructed distance of 100 ft (30.5 m). You must turn on the ir setting from the 4BAR Flex Q ILS and navigate to Auto mode before using the footswitch.
  • Page 14: Irc-6 Infrared Remote Control

    Master/Slave Mode (D-Fi USB) The D-Fi USB allows a single 4BAR Flex Q ILS product (the “master”) to control the actions of one or more 4BAR Flex Q ILS products (the “slaves”) without the need of a DMX controller or DMX cables. The master (transmitter) product will be set to operate in standalone mode, while the slave (receiver) products will be set to operate in DMX mode.
  • Page 15: Maintenance

    6. Softly drag any dirt or grime to the outside of the transparent surface. 7. Gently polish the transparent surfaces until they are free of haze and lint. Always dry the transparent surfaces carefully after cleaning them. Page 14 of 17 4BAR Flex Q ILS User Manual Rev. 1...
  • Page 16: Technical Specifications

    Technical Specifications 6. Technical Specifications Dimensions and Weight Length Width Height Weight 4BAR Flex Q ILS 45.7 in (1,186 mm) 2 in (50 mm) 12 in (305 mm) 12.2 lb (5.5 kg) Wireless 16.5 in (419 mm) 5.2 in (132 mm) 1.5 in (38 mm)
  • Page 17: Returns

    Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be your responsibility. FedEx packing or double-boxing are recommended. Chauvet reserves the right to use its own discretion to repair or replace returned product(s). Page 16 of 17 4BAR Flex Q ILS User Manual Rev. 1...
  • Page 18: Contact Us

    Visit the applicable website above to verify our contact information and instructions to request support. Outside the U.S., U.K., Ireland, Mexico, France, Germany, or Benelux, contact the dealer of record. 4BAR Flex Q ILS User Manual Rev. 1 Page 17 of 17...

Table of Contents