Page 2
Edition Notes The 4BAR LTBT ILS User Manual includes a description, safety precautions, installation, programming, operation, and maintenance instructions for the 4BAR LTBT ILS as of the release date of this edition. Trademarks Chauvet, Chauvet DJ, the Chauvet logo, and 4BAR are registered trademarks or trademarks of Chauvet &...
Important installation or configuration information. The product may not function correctly if this information is not used. Useful information. 4BAR LTBT ILS User Manual Rev. 1...
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and the user. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 4BAR LTBT ILS User Manual Rev. 1...
Auto colors mode / Strobe programs 9-Volt battery Power cover switch WARNING! DO NOT plug anything other than a D-Fi USB into the USB Port. Doing so may cause damage to the product. 4BAR LTBT ILS User Manual Rev. 1...
Product Dimensions Front View 36 in 918 mm 33 in 830 mm 11 in 274 mm Side View 2 in 44 mm 11 in 274 mm 43 in 1084 mm 17 in 444 mm 4BAR LTBT ILS User Manual Rev. 1...
3. Setup AC Power The 4BAR LTBT ILS has an auto-ranging power supply, and it can work with an input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart.
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The 4BAR LTBT ILS may be mounted in any position; however, make sure adequate ventilation is provided around the product. Rigging • Before deciding on a location, always make sure there is easy access to the product for maintenance and programming.
Chauvet & Sons, LLC is under license. Other trademarks and trade names are those of their respective owners. DMX Linking The 4BAR LTBT ILS works with a DMX controller. Information about DMX is in the Chauvet DMX Primer available from the Chauvet website: http://www.chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf.
Operation D-Fi USB Connectivity The 4BAR LTBT ILS is able to become a D-Fi wireless receiver/transmitter with the use of the D-Fi USB from Chauvet DJ. Simply set the DIP switch D-Fi receiving/transmitting channel, plug it into the USB port then set the product’s DMX Personality and DMX Address.
DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller. Static Colors To run the 4BAR LTBT ILS in Preset Color mode, follow the instructions below: 1. Press <MENU> repeatedly until C-- shows on the display. 2. Press <ENTER>.
Operation Wireless Footswitch The included wireless footswitch provides quick access to preset colors, color-change programs, and sound-activation through the 4BAR LTBT ILS microphone. To use the footswitch: Connect the 4BAR LTBT ILS to power. Turn the wireless footswitch on. Press <MENU> on the 4BAR LTBT ILS until SEt shows on the display, and press <ENTER>.
Operation IRC-6 Infrared Remote Control The 4BAR LTBT ILS is compatible with the IRC-6 infrared remote control from Chauvet. To activate IR mode, follow the instructions below: 1. Press <MENU> repeatedly until SEt shows on the display. 2. Press <ENTER>.
D-Fi USB Master/Slave Mode The D-Fi USB allows a single 4BAR LTBT ILS product (the “master”) to control the actions of one or more 4BAR LTBT ILS products (the “slaves”) without the need of a DMX controller or DMX cables. The master (transmitter) product will be set to operate in either standalone mode or with the footswitch, while the slave (receiver) products will be set to operate in slave mode.
For wired Expansion mode, configure the products as indicated below. Slave products: 1. Set the slave products to 3-channel mode, 3Ch. 2. Set the DMX address of each slave product to correspond with the pod on the 4BAR LTBT ILS being synchronized with, as follows: •...
ILS mode. This product will synchronize with the wash effect on the selected par of the GigBAR MOVE+ILS. To set the 4BAR LTBT ILS to respond to an ILS signal: 1. Press <MENU> repeatedly until iLS_ shows on the display.
6. Softly drag any dirt or grime to the outside of the transparent surface. 7. Gently polish the transparent surfaces until they are free of haze and lint. Always dry the transparent surfaces carefully after cleaning them. 4BAR LTBT ILS User Manual Rev. 1...
For warranty terms and conditions and return information, please visit our website. For customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration. For customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, and Germany: www.chauvetlighting.eu/warranty-registration. 4BAR LTBT ILS User Manual Rev. 1...
Need help?
Do you have a question about the 4BAR LTBT ILS and is the answer not in the manual?
Questions and answers