Advertisement
Quick Links
Note: The method of manual override can either be selected to operate from the valet switch or operate as custom
code. Be certain to place a check mark indicating the method used in the box located on the last page of
the owner's manual.
Note: When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver's door pin
switch in order to begin the passive arming sequence.
RF Programmable Features :
Feature Selection
1st Door L/UL
2nd Accy Lock
3rd Accy. UL
4th Headlights
5th Passive Locks
6th Passive/Active Arm
7th Voltage Sense
8th Siren/Horn
9th Horn Chirp
10th Override Method
11th Two Step Unlock
12th Chirp Delete From Tx
To program these selectable features;
Turn ignition on
Press and release the valet switch 3 times
Within 3 seconds, turn ignition Off
First
Then On
Press transmitter Lock button to change
Press transmitter Lock button to change
Second
Press and release the valet switch
Press transmitter Lock button to change
Third
Press and release the valet switch
Press transmitter Lock button to change
Press transmitter Lock button to change
SELECTABLE FEATURES
1 Chirp
2 Chirps
1 Sec.
3.5 Sec.
Auto Lock On
Auto Lock Off
Auto UL Dr.
Auto UL All
On Arm
On Disarm
Passive
Active
Passive Arm
Active Arm
Voltage Sense
Hardwire
Siren/Horn
Siren Only
10mS
16mS
Custom Code
Valet
On
Off
On
Off
Action
or
or
or
Model APS-610a
Installation Manual
3 Chirps
4 Chirps
1 Sec L, Dbl. U/L
Auto UL Off
On Both
Off
Horn Only
30mS
System Response
No response
1 Chirp - LED 1 flash
Short chirp, then long chirp
1 chirp = 1 second door locks
2 chirps = 3.5 second door locks
3 chirps = 1 sec. lock, dbl 1 sec. unlock
2 chirps = auto locks off
1 chirp = auto locks on
3 chirps = auto unlock off
1 chirp = auto unlock drivers door only
2 chirps = auto unlock all doors
Default
1 Sec.
Auto Lock Off
Auto UL Off
Both
Active
Active Arm
Hardwire
Siren/Horn
16mS
Valet
Off
Off
128-6539
1 of 10
Advertisement
Related Manuals for Audiovox Prestige Platinum APS-610A
Summary of Contents for Audiovox Prestige Platinum APS-610A
- Page 1 Model APS-610a Installation Manual SELECTABLE FEATURES Note: The method of manual override can either be selected to operate from the valet switch or operate as custom code. Be certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.
- Page 2 Fourth Press and release the valet switch 3 chirps = headlight output when arming and disarming Press transmitter Lock button to change 4 chirps = headlight output off Press transmitter Lock button to change 1 chirp = headlight output when arming Press transmitter Lock button to change 2 chirps = headlight output when disarming Fifth...
- Page 3 If during the program sequence receiver channel 1 is programmed, and received channel 2 is skipped over, as indicated in the transmitted program guide, then the unit will operate as a single button lock/unlock unit from that transmitter. It is possible to have one transmitter programmed for single button lock/unlock, and one transmitter programmed for separate button lock/unlock if the customer so desires.
-
Page 4: Wiring The System
WIRING THE SYSTEM Large 10 Pin Edge Connector: Red/White (5Amp) & Red (15Amp) Fused Wires: +12 VDC Constant Battery Source This wire controls the sensitivity of the voltage sensing circuit, which detects the turning on of an interior light when a door is opened. It will also detect the switching on of parking or headlamps, and in many cases will trigger the alarm when a thermostatically controlled electronic radiator cooling fan switches on. - Page 5 Note: This is a normally closed starter cut arrangement, and when power is removed from the security system, the starter disable feature will not operate, allowing the vehicle to start. Audiovox does not recommend using the Orange wire to interrupt anything but the starting circuit of the vehicle.
- Page 6 Audiovox does not recommend using the Orange w/ White trace wire to interrupt anything but the starting circuit of the vehicle. Dark Green Wire: ( - ) INSTANT TRIGGER ZONE This is an instant on ground trigger wire. It must be connected to the previously installed hood and trunk pin switches.
- Page 7 Route the red and blue wires in the 2 pin white connector from the LED to the control module, and plug it into the mating white connector on the side of the module. 4 Pin White Connector: Shock Sensor Route the red, black, green and blue wires in the 4 pin white connector from the shock sensor to the control module, and plug one end into the shock sensor, and the other end into the mating white connector on the side of the module.
-
Page 8: Completing The Installation
These applications require the use of additional components which may include relays, fixed resistors, or for convenience, the AS 9159 Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supplement and or the Audiovox fax back service for information on your particular vehicle for properly connecting to these types of circuits. - Page 9 NOTE: This unit has the ability to learn the dome light delay time, up to 60 seconds. If the vehicle has delay interior lights, and you wish to avoid three chirp, defect zone, indication normally associated with this type of interior light, we suggest you learn the interior light delay. To learn the light delay, start with all doors closed: (1) Use the transmitter to Lock / Unlock / Lock / Unlock / Lock / Unlock / Lock, the system.
- Page 10 © 2003 Audiovox Electronic Corporation, 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-6539 128-6539 10 of 10...