Related Manuals for emaux APS Series
Summary of Contents for emaux APS Series
- Page 1 HYDRAU-POWER PLASTIC PUMP APS SERIES OWNER'S MANUAL Installation and Operation USER MANUAL Model: APS Series EMPU22121601...
-
Page 2: Table Of Contents
TABLE OF CONTENT ..WARNINGS AND SAFETY INSTRUCTIONS ..SUCTION ENTRAPMENT HAZARD ..1. APS SERIES PLASTIC PUMP OVERVIEW ..2. PRODUCT INFORMATION 3. IMPORTANT SAFETY INSTRUCTIONS ..4. TRANSPORT AND STORAGE 5. INSTALLATION ..5. 1 LOCATION 5. 2 PIPING 5. -
Page 3: Warnings And Safety Instructions
WARNINGS AND SAFETY INSTRUCTIONS GENERAL WARNING This instruction contain general caution information for use in Pool and SPA pump installation application. Specified Pump model function should be refer to particular manual. Components such as the filtration system, pumps and heater must be positioned so as to prevent their being used as means of access to the pool by young children. -
Page 4: Suction Entrapment Hazard
SUCTION ENTRAPMENT HAZARD This pump produces high levels of suction and creates a strong vacuum at the main drain at the bottom of your pool and spa. This suction is so strong that it can trap adults or children under water if they come in close proximity to a pool or spa drain or a loose or broken drain cover or grate. -
Page 5: Aps Series Plastic Pump Overview
1. APS SERIES PLASTIC PUMP OVERVIEW 1. Hydrau-Power APS series pump delivery Emaux latest technology in pump design. 2. It is constructed in reinforced plastic pump body in lightweight and corrosion-resistant that suitable for marine applications. -
Page 6: Product Information
2. PRODUCT INFORMATION Horsepower Code Donnection Size Strainer Model No (Hp) 380V/50Hz ANSI/DIN 9023901 APS550P 4” / DN 100 2850 9023902 APS750P 4” / DN 100 2850 9023903 APS1000P 6” / DN 150 1450 9023904 APS1500P 6” / DN 150 1450 Dimension (mm) 940(5.5HP) / 970(7.5HP) -
Page 7: Important Safety Instructions
1450RPM 50Hz U.S.g.p.m 1200 H(ft) H(m) 55 60 65 70 75 80 85 85 Q(m³/h) Q(LPM) 1500 2250 3000 3750 4500 3. IMPORTANT SAFETY INSTRUCTIONS The user guide you are holding includes essential information on the safety measures to be implemented for installation and start-up. -
Page 8: Installation
5. INSTALLATION 5. 1 LOCATION The pump should be located nearby as close as possible the pool or spa to reduce friction loss and improve efficiency. It is recommended at least 1.5 meter from pool water and 3 meters according to Canadian code. 1. -
Page 9: Electrical Wiring-3 Phase
6. ELECTRICAL WIRING-3 PHASE This power pump demand licensed or certified electrician or qualified pool installer to ensure there is adequate protection between the pump motor and mains power supply according to individual countries safety code. The pump has power cord with plug attached on the plug, plug it to a power socket with circuit breaker to isolate the motor from the mains power for over load protection. -
Page 10: Direct On Line
6. 1 DIRECT ON LINE Direct On Line (DOL) starting is the simplest, cheapest and most common starting method. It actually gives the lowest temperature rise within the motor during startup of all the starting methods. But the drawback is starting current can be 3-8 time of full load current. -
Page 11: Star/Delta Starter
The factory connection is a Dealta conneciton 3 phase power 4 wires power line connection Green& yellow Groudn wire location Terminal Box Motor Roation Arrow 1. Every power lines have to be protected by circuit breaker for over load to isolated the motor from the mains power and provide protection to motor. -
Page 12: Variable Frequency Drive(Vfd)
Contactor Protection Relay with Motor Circuit timer Breaker The contact plate on the six terminals has to be removed. 6. 3 VARIABLE FREQUENCY DRIVE(VFD) The pump is possible to drive by variable frequency driver for better starting and energy saving purpose. The connection is simple, it is just connect the 3 phase output of the variable frequency drive to the pump in Delta or Star configuration according to the motor plate on the motor. -
Page 13: Soft Starter
Besides current and power rating of the VFD is the key parameter to drive the motor, the EMC filter between VFD and motor is the most critical device to prevent the motor bearing, shaft and insulation system from being damage by VFD inverter high frequency bearing current noise. -
Page 14: Start Up
7. START UP 1. Verify the pump shaft turn freely. 2. Check the mains voltage, current and frequency are accordingly to the name plate. 3. Never run pump dry! Running pump dry may cause damage to the mechanical seal causing leakage and flooding. -
Page 15: Rountine Maintenance Schedule
The pump mechanical seal requires no lubrication and service. To avoid drops in pressure and pre-filter Basket damage. The pre-filter basket of the pump should be visually inspected at least once a week. Remove the clear lid and the basket and clean debris from basket. Inspect the lid O-ring;... -
Page 16: Trouble Shooting
10. TROUBLE SHOOTING Problem Corrective Action 1. No water in Pre-filter Lid is not tight Damaged lid O-Ring 2. Water level below Skimmer 3. Pre-filter or Skimmer Basket clogged Closed Valve in Piping System Pump Will Not Prime 4. Air leak in Suction Line 5. - Page 17 Descriptions Diameter of inlet and outlet of the pump Diameter of the Pipe Air-bleed hole should be installed at the highest point Holding the pipes with racks so as to prevent too much load on the branch of the pump, and the racks should be coated with corrosion resisting material.
-
Page 18: Replacement Parts
12. REPLACEMENT PARTS 11 13 14 17 18 12 16 Product Description Key NO Part NO 420386559 Transparent Lid(APS5.5HP-7.5HP) 420386556 Transparent Lid(APS10HP-15HP) Neck Clip(APS5.5-APS7.5HP) 420556559 Neck Clip(APS10HP-15HP) 420556556 Lid Fastener(APS5.5HP-7.5HP) 420566559 Lid Fastener(APS10HP-15HP) 420566556 Transparent Lid O-Ring(APS5.5HP-7.5HP) 111010040 Transparent Lid O-Ring(APS10HP-15HP) 111010037 Basket(APS5.5HP-7.5HP) 420236559... -
Page 19: Terms Of The Warranty
It is not transferable to anyone who subsequently purchases the product from you. It excludes all expendable parts. During the warranty period, Emaux authorized reseller will repair or replace defective parts with new parts or, at the option of Emaux, serviceable used parts that are equivalent or superior to new parts in performance. - Page 20 EMAUX WATER TECHNOLOGY CO., LTD YOUR PREMIER SUPPLIER www.emauxgroup.com...
Need help?
Do you have a question about the APS Series and is the answer not in the manual?
Questions and answers