Related Manuals for Malmsten 1511001
Summary of Contents for Malmsten 1511001
- Page 1 Art. No. 1511001 Water Polo Goal Malmsten Unassembled (1511001) Assembly Instructions...
- Page 2 Installation manual www.malmsten.com Art. No. 1511001 TOOLS AND EQUIPMENT REQUIRED TOOLS AND EQUIPMENT REQUIRED TOOLS AND EQUIPMENT RECOMMENDED (OPTIONAL) Hex key #5 (included) Hex key #5 (included) Blankets, soft lining or protection tiles (velour surface) Hex key #6 (included) Hex key #6 (included)
- Page 3 Art. No. 1511001 DIN 125 10,5 washer 2 pcs DIN 985 M10 nut 6 pcs DIN 127 A8 spring DIN 125 A8,4 washer 6 pcs 6 pcs washer DIN 9021 A8,4 DIN 985 M8 nut 12 pcs 8 pcs...
- Page 4 Art. No. 1511001 Step 2 – assembly Assembling the front frame Attention! Lacquered parts of the goal are fragile! Please assemble them on a flat, debris-free surface (preferably on a carpet or other soft lining). Assemble the crossbar using: Crossbar (6) –...
- Page 5 Art. No. 1511001 Assembling the floats 2.3.1 Install the positioning sleeve to the floats using: Positioning sleeve (9) – 2 pcs Right float (1) – 1 pcs Left float (2) – 1 pcs Clamping plate (14) – 2 pcs DIN 912 Hex socket cap screw M10x100 (28) –...
- Page 6 Art. No. 1511001 2.3.6 Additionally secure the connection of floats with the following bolts: DIN 985 M8 nut (21) – 4 pcs DIN 9021 A8,4 enlarged stainless steel washer (22) – 8 pcs DIN 912 Hex socket cap screw M8x25 (26) – 4 pcs 2.3.7...
- Page 7 Art. No. 1511001 Assembling the net support Connect the straight tube (10) with the L-shaped tube (11) using: DIN 985 M8 nut (21) – 4 pcs DIN 912 Hex socket cap screw M8x45 (27) – 4 pcs End result: Assembling the front frame with floats Use the following parts to connect the goal’s frame with...
- Page 8 Art. No. 1511001 Connect the previously assemble tubes (10) & (11) to the: Front frame using: Floats using: DIN 125 A8,4 washer (19) – 2 pcs Rubber distance pad (37) – 4 pcs DIN 985 M8 nut (21) – 2 pcs (one pad on each side, with a flat part directed outside) DIN 6912 socket head screws (low head) M8x60 (31) –...
- Page 9 Art. No. 1511001 Connect the net support side-tubes with the straight pipe (8) using: Rubber distance pad (37) – 8 pcs Star knob (with M8x65 bolt) (40) – 2 pcs 2.5.1 Important notice The goal can be fold easily to storage position by removing the star-knobs (38 & 39) and by...
- Page 10 Art. No. 1511001 Installation of the castors Assemble 4 castors (16) to the bas of the goal with the use of: DIN 985 M10 nut (18) – 4 pcs Eyelet screw with metric thread (25) – 4 pcs DIN 9021 A10,5 enlarged washer (A4) – 4 pcs...
- Page 11 Art. No. 1511001 Installation of the net ` Use provided “omega” net hooks to install the net to the goal’s frame and floats, by placing the net inside the hook and then putting it into the groove in the profile: Put one “omega”...
- Page 12 Art. No. 1511001 III. Maintenance and Service To ensure long-lasting and safe use of the equipment, periodical inspections are required: • Every time before using the equipment: • Visually check if there are any parts damaged or missing • Check if all the devices are installed correctly and secured to prevent tilting/moving •...
-
Page 13: Terms Of Warranty
IV. TERMS OF WARRANTY General Provisions 1.1 M. MALMSTEN AB (the “Manufacturer”) provides the limited warranty (the “Warranty”) to the purchaser of the Equipment. Warranty is only valid in the facility in which the Equipment was originally installed. The Warranty is valid from the time of the final acceptance of the building or from the date of delivery and to the timeline listed below, under the terms and conditions stated below. -
Page 14: Location Of The Serial Number
Art. No. 1511001 Exclusions and Conditions: • Operations, which shall be made by the user and on his cost, such as maintenance of cleanli- ness, periodical checkups (as in point 2.1) • Mechanical and chemical damages caused by improper use and maintenance (i.e. attempts of self-repair;...