Related Manuals for Electrolux Professional W4 H Series
Summary of Contents for Electrolux Professional W4 H Series
- Page 1 Installation manual Washer extractor W4400H, W4600H, W4850H, W41100H Clarus Control Type W4.H. 438921181/EN Original instructions 2022.08.15...
-
Page 3: Table Of Contents
Contents Contents 1 Safety Precautions ..........................5 General safety information......................6 Commercial use only........................6 Symbols............................6 2 Warranty terms and exclusions......................7 3 Technical data.............................8 Drawing ............................8 3.1.1 W4400H .........................8 3.1.2 W4600H .........................9 3.1.3 W4850H ........................10 3.1.4 W41100H ........................11 Technical data .........................12 Connections ..........................12 4 Setup ...............................13 Unpacking ..........................13 Recycling instruction for packaging ...................16... -
Page 5: Safety Precautions
Installation manual 1 Safety Precautions • Servicing shall be carried out only by authorized personnel. • Only authorized spare parts, accessories and consumables shall be used. • Only use detergent intended for water-wash of textiles. Never use dry cleaning agents. •... -
Page 6: General Safety Information
Installation manual – This appliance is intended to be used in household and similar applications such as: (IEC 60335-2-7) staff kitchen areas in shops, offices and other working environments, farm houses, by clients in hotels, motels and other residential type environments, bed and breakfast type environments, areas for communal use in blocks of flats or in launderettes. -
Page 7: Warranty Terms And Exclusions
Warranty will be applicable where the customer has used only genuine spare parts and has performed maintenance in accordance with Electrolux Professional user and maintenance documentation made available in paper or elec- tronic format. Electrolux Professional strongly recommends using Electrolux Professional approved cleaning, rinse and descaling agents to obtain optimal results and maintain product efficiency over time. -
Page 8: Technical Data
Installation manual 3 Technical data 3.1 Drawing 3.1.1 W4400H 11,5° 11,5° Operating panel Door opening, ⌀ 535 mm Five-compartment detergent box, front (optional) Five-compartment detergent box, right hand side (optional) Cold water Hot water Third water (optional) Steam connection Drain Electrical connection Compressed air connection External liquid detergent connections, 6 pcs ⌀... -
Page 9: W4600H
Installation manual 3.1.2 W4600H 11,5° 11,5° Operating panel Door opening, ⌀ 535 mm Five-compartment detergent box, front (optional) Five-compartment detergent box, right hand side (optional) Cold water Hot water Third water (optional) Steam connection Drain Electrical connection Compressed air connection External liquid detergent connections, 6 pcs ⌀... -
Page 10: W4850H
Installation manual 3.1.3 W4850H Operating panel Door opening, ⌀ 700 mm Five-compartment detergent box, front (optional) Five-compartment detergent box, right hand side (optional) Cold water Hot water Third water (optional) Steam connection Drain Electrical connection Compressed air connection External liquid detergent connections, 6 pcs ⌀ 10 mm, 1 pc ⌀ 16 mm and 1 pc ⌀ 20 mm Water connection, detergent injector, 3/4”... -
Page 11: W41100H
Installation manual 3.1.4 W41100H Operating panel Door opening, ⌀ 700 mm Five-compartment detergent box, front (optional) Five-compartment detergent box, right hand side (optional) Cold water Hot water Third water (optional) Steam connection Drain Electrical connection Compressed air connection External liquid detergent connections, 6 pcs ⌀ 10 mm, 1 pc ⌀ 16 mm and 1 pc ⌀ 20 mm Water connection, detergent injector, 3/4”... -
Page 12: Technical Data
Installation manual 3.2 Technical data W4400H W4600H W4850H W41100H Weight, net 1095–1450* 1380–1480* 2200–2300* 2300–2400* Drum volume litres 1100 Drum diameter 1220 1220 Drum speed during wash Drum speed during extraction G-factor, max. Heating: Electricity 36.0 38.4 54.0 Heating: Steam Heating: Hot water Frequency of the dynamic force 13.8... -
Page 13: Setup
Installation manual 4 Setup 4.1 Unpacking The direction from which the machine must be lifted and the machine centre of gravity are shown on the packaging. Remove the side panels, the rear panel and the lower front panel. fig.5542 Remove the eight bolts securing the machine’s outer- and inner frame onto the pallet. Note! If the machine is equipped with weighing equipment, take extra care when removing the bolts, since the load cells fitted by the machine’s feet are sensitive to knocks and impacts. - Page 14 Installation manual Use a fork-lift truck to lift the machine. fig.5545 Position the four blocks of wood supplied, one beneath each machine foot (on the outer frame), within the recesses in the pallet. fig.7222 Lower the machine (A) and withdraw the truck forks (B). The machine should now be standing on the four blocks, and the pallet will be on the floor, clear of the machine.
- Page 15 Installation manual Lift the machine and remove pallet and blocks. fig.5548 The feet can be of two types: fixed feet or rotating feet if the machine is to be fitted with tilt or weighing equipment. For machines with tilt or weighing equipment: screw on the machine’s feet. Note! If the machine is to have the tilt function, this is a suitable time to install the corner posts which hold the pro- tective plates, and also, where applicable, the position sensors.
-
Page 16: Recycling Instruction For Packaging
Installation manual 4.2 Recycling instruction for packaging fig.X02411 Fig. Description Code Type Wrapping film LDPE 4 Plastics Screw FE 40 Steel Packaging FOR 50 Wood Pallet FOR 50 Wood Screw FE 40 Steel Washer FE 40 Steel Plastic bag PET 1 Plastics... -
Page 17: Siting
Installation manual 4.3 Siting The machine must not be sited over an open floor drain. Check that the floor has an even surface and is in level. The machine should be positioned so that there is plenty of room for working, both for the user and service personnel. The figure shows minimum distance to a wall and/or other machines. - Page 18 Installation manual Standard machines W4400H W4600H W4850H W41100H 1325 1390 1640 1640 1445 1605 1635 1850 1160 1315 1370 1585 1310 1370 1610 1610 FRONT fig.W00141...
- Page 19 Installation manual Machines with tilt or weighing equipment W4400H W4600H W4850H W41100H 1325 1390 1640 1640 1445 1605 1635 1850 1170 1325 1380 1600 1340 1400 1640 1640 –10 –10 1140 P = tilting devices FRONT fig.W00142 Use a spirit level and, where necessary, the washers (or rectangular metal plates) supplied, to ensure that the floor mountings are in level.
- Page 20 Installation manual Put the machine in place. Use a spirit level on suitable surfaces of the outer frame to check that the machine is in lev- el. Also check that the machine is resting firmly on all four feet. fig.5551 Bolt the machine feet to the floor.
-
Page 21: Water Connection
Installation manual 5 Water connection All water intake connections to the machine should be fitted with manual shut-off valves and filters, to facilitate instal- lation and servicing. Water pipes and hoses should be flushed clean before installation. The machine shall be connected with new water hoses. Re-used water hoses must not be used. Hoses are to be of an approved type and grade and comply with IEC 61770. -
Page 22: Steam Connection
Installation manual 6 Steam connection The supply hose must be equipped with a manual shut-off valve to facilitate installation and servicing. Fit filter to the manual shut-off valve. Connections with pipes directly to the machine are not allowed. Connect the hose so it hangs in a gentle arc. (This is particularly important if the machine is fitted with a tilting function). -
Page 23: Compressed Air Connection
Installation manual 7 Compressed air connection A pressure regulator complete with water separation device is to be installed on the machine. When the machine is supplied, the angled coupling (A), hose (B) and bracket (C) for the pressure regulator will al- ready be installed. -
Page 24: Drain Connection
Installation manual Connect the hose from the compressed air supply to the bushing on the pressure regulator. Connect the hose so it hangs in a gentle arc. (This is particularly important if the machine is fitted with a tilting function). The connecting hose must be rated for a pressure of at least 1 MPa. -
Page 25: Ventilation
Installation manual 9 Ventilation The vent (A) from the machine drum is at the back of the machine. If bleach or other additives are used, the pipe should be extended and connected to a ventilation system. fig.5872A 10 Detergent supply injector If only non-liquid detergents are to be used in the detergent supply injector, the following adaptation is recommended: Drill two ⌀... -
Page 26: Connection Of External Dosing Systems
Installation manual 11 Connection of external dosing systems 11.1 Connection of the hoses Note! All external equipment which is connected to the machine must be CE/EMC-approved. The machine is prepared for connection of external dosing systems or water re-use systems etc. The connections are closed at delivery. -
Page 27: Electrical Connection Of External Dosing System
Installation manual 11.2 Electrical connection of external dosing system The electrical installation may only be carried out by qualified personnel. The external dosage unit connects to the X146 via the upper terminal in the coin operation unit. There are a total of 8 outlets for the dosing of washing detergent. -
Page 28: Electrical Connection
Installation manual 12 Electrical connection The electrical installation may only be carried out by qualified personnel. The electrical cable for the machine's power supply should hang in a gentle arc. (This is particularly important if the machine is fitted with a tilting or weighing function). Connect the machine to a separate mains circuit with its own circuit breaker(s). - Page 29 Installation manual Switching to 208V or 200–208V Remove the middle panel at the back of the machine and remove the protective plate covering the transformer. fig.W00899 Reconnect the primary power supply to the transformer as follows: W4400H Move the cables from position A to position B for a 208 V supply.
-
Page 30: Electrical Connections
Installation manual 12.1 Electrical connections W4400H Heating alternative Main voltage Heating power Total power Recommended fuse Electric heated 220-240V 3 ~ 50/60 36.0 38.0 380-415V 3 ~ 50/60 32.8 34.8 440/480V 3 ~ 50/60 36.0 38.0 63/50 220V 3 ~ 50/60 32.9 35.0... -
Page 31: Installation Of Machines With Tilt Function
Installation manual 13 Installation of machines with tilt function Remove the side panels, the rear panel and the lower front panel. fig.3449 For machines with tilt both forwards and backwards Insert the two cylinder units (A) from the side of the machine underneath the machine frame. If there is vinyl floor-covering on the floor: To protect the floor from wear, a sheet of stainless steel should be laid be- neath each cylinder. - Page 32 Installation manual Secure the cylinder units using four bolts and nuts. Note! It is important to fit four washers (B) (each 5 mm thick) between each cylinder unit and the machine frame. fig.3453A Fit the four corner posts, one for each corner of the machine, using the bolts which secure the machine feet to the floor.
- Page 33 Installation manual For machines with tilt both forwards and backwards Fit two pneumatic position sensors (C) on two of the machine feet: at left-hand front and right-hand rear, diagonally opposed. The position sensors are to be fitted using the inner two fastening bolts of the feet, mounted on the corner posts just installed.
- Page 34 Installation manual Note that the tubes for the pressure sensors must be connected correctly. • Connection 1 – same side as data plate. • Connection 2 – same side as the inset white plate. fig.6026 For machines with forward tilt only The compressed air line to be connected to the air bellows is supplied bundled on the machine rear.
- Page 35 Installation manual Before refitting the panels, test the tilt function: • Switch on the machine electrical switch(es) and turn on the compressed air supply. • Open the door and lock it open. • The uppermost switch on the tilt control unit tilts the machine either backwards (turn switch counter clockwise) or forwards (turn switch clockwise).
- Page 36 Installation manual Fit the rubber dampers (E) and sleeves (F) to the front end of each side panel strip. Washer (G), nut (H), screw (I). fig.3485A Position and fasten the side panel strips. fig.3486...
- Page 37 Installation manual Fit the two counterweights to the front panel strip. The bolt heads should be at the bottom. fig.3487 Hang the front panel strip on the two sleeves fitted to the side strips. Protective plates are mounted on the front and rear.
-
Page 38: Disposal Information
Installation manual 14 Disposal information 14.1 Disposal of appliance at end of life Before disposing of the machine, make sure to carefully check its physical condition, and in particular any parts of the structure that can give or break during scrapping. The machine’s parts must be disposed of in a differentiated way, according to their different characteristics (e.g. - Page 40 Electrolux Professional AB 341 80 Ljungby, Sweden www.electroluxprofessional.com...
Need help?
Do you have a question about the W4 H Series and is the answer not in the manual?
Questions and answers