Download
Share
Print this page
Exmark ULTRA VAC UVD6672 Setup Instructions
  1. Manuals
  2. Brands
  3. Exmark Manuals
  4. Lawn Mower Accessories
  5. ULTRA VAC UVD6672
  6. Setup instructions
Exmark ULTRA VAC UVD6672 Setup Instructions

Exmark ULTRA VAC UVD6672 Setup Instructions

Quick dump system for lazer z models
Hide thumbs Also See for ULTRA VAC UVD6672:

Advertisement

Quick Links

Download this manual
Loose Parts
Use the chart below to verify that all parts have been shipped. Part numbers not shown are available on the dealer
extranet.
Dealer Pack
Part #
3296-2
3256-61
32105-13
Literature Pack
Manual, Operator's
Model Numbers
UVD60–Fits Lazer Z (LZ), Lazer Z AS (LAS), Lazer Z XP Units 352,000–789,999 and Lazer Z XS Units 352,000
and Higher, and Lazer Z DS (LZDS) 312,000,000 and Higher with 60 inch deck.
UVD6672–Fits Lazer Z (LZ), Lazer Z AS (LAS), and Lazer Z XP Units 352,000–789,999 and Lazer Z XS Units
352,000 and Higher with 66 inch or 72 inch deck, and Lazer Z DS (LZDS) 312,000,000 and Higher with 72 inch deck.
© 2014—Exmark Mfg. Co., Inc.
P.O. Box 808
Beatrice, NE 68310
(to fit Lazer Z (LZ), Lazer Z AS (LAS), and Lazer Z XP Units 352,000–789,999)
Description
Nut, Nyloc #10-24 inch
Washer
Screw, HWH #10-24 x 3/4 inch
ULTRA VAC
QUICK DUMP SYSTEM
Setup Instructions
For Ultra Vac Serial Nos. 315,000,000 & Higher
(to fit Lazer Z XS Units 352,000 & Higher)
(to fit Lazer Z DS Units 312,000,000 & Higher)
Qty.
3
3
Assembling the tubes.
3
All Rights Reserved *4502-222* A
Part No. 4502-222 Rev. A
Printed in the USA.
Lazer Z
Models
®
Use
®

Advertisement

loading
Need help?

Need help?

Do you have a question about the ULTRA VAC UVD6672 and is the answer not in the manual?

Questions and answers

Related Manuals for Exmark ULTRA VAC UVD6672

Summary of Contents for Exmark ULTRA VAC UVD6672

  • Page 1 UVD6672–Fits Lazer Z (LZ), Lazer Z AS (LAS), and Lazer Z XP Units 352,000–789,999 and Lazer Z XS Units 352,000 and Higher with 66 inch or 72 inch deck, and Lazer Z DS (LZDS) 312,000,000 and Higher with 72 inch deck. © 2014—Exmark Mfg. Co., Inc. All Rights Reserved *4502-222* A Part No.
  • Page 2 Models and Required Completing Kits Note: Use the following charts to verify the kits required for the unit you are installing the UltraVac on. UNIT SERIAL NUMBER REQ'D TO MOUNT ULTRA VAC 109-1179 Drive Kit and Lazer Z 604 (Includes AS) 510,000–789,999 103-5633 Front Weight Kit Lazer Z 604 (Includes AS)

  • Page 3: Assembly Diagrams

    Assembly Diagrams All XS Liquid-Cooled All XS, XP Below 600,000 & Higher 600,000 & 60 AS 510,000– All LZ 600,000 All XS All LZDS 60 & 72 LZ and 789,9999 60 & 72 LZ —789,999 Air-Cooled 312,000,000 & AS 352,000-509,999 510,000-599,999 with Triton deck 600,000 &...
  • Page 4 All XS Liquid-Cooled All XS, XP Below 600,000 & Higher 600,000 & 60 AS 510,000– All LZ 600,000 All XS All LZDS 60 & 72 LZ and 789,9999 60 & 72 LZ —789,999 Air-Cooled 312,000,000 & AS 352,000-509,999 510,000-599,999 with Triton deck 600,000 &...
  • Page 5 Figure 1 All Lazer Z XP & Lazer Z XS Serial Number 510,000 & Higher and Lazer Z Serial Number 510,000–789,999 (Shown without ROPS for clarity) *Lazer Z XS Liquid-Cooled Units Serial Number 600,000 and Higher and Lazer Z DS Serial Number 312,000,000 and Higher require an additional weight (item 33) on the front panel.
  • Page 6 Safety Safety Alert Symbol This Safety Alert Symbol (Figure 3) is used both in this setup instructions and on the machine to identify important safety messages which must be followed to avoid accidents This symbol means: ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Figure 4 1.
  • Page 7 bumper bars to the vertical “HOT” engine guard shield using two of the original screws, washers and whizlock nuts removed from the bumper plate. 2. Remove the lower two screws holding the clutch guard plate (“HOT” engine guard on liquid–cooled units) to the rear frame of the Lazer Z unit.
  • Page 8 Note: On units with a ROPS installed, the lower washer and whizlock nut. These items are included front screw that attaches to the wheel motor channel with ROPS kit number FRPSLZ. must be left uninstalled. Units with Serial Number Note: On 60 inch units, the lower bolt on the 440,000 through 509,999 will have a captured bolt in wheel channel is best installed by positioning the nut this position (see Figure 7).

  • Page 9: All Units

    Figure 9 4. Install the frame brackets (item 16), and ROPS lower roll bar tubes loosely to the mounting pads on both sides of the Lazer frame. Use the ROPS mounting Figure 10 hardware, eight 3/8-16 x 1 1/2 inch screws, eight 3/8 1.

  • Page 10: Installing The Blower Assembly

    All Units: Apply a light coat of grease to the front and rear of the upper tube of the mount weldment. Install the hopper assembly (item 1) onto the mount by slipping the hook portion over the top mounting tube of the mount weldment.
  • Page 11 Use special tool 109-2979 to hold spindle from rotating. Do Not use the blade bolt to prevent rotation. Figure 13 1. Torque sheave nut to 2. Install with cone towards 140-145 ft-lb (190–197 nut. N-m). Check blade bolt torque after completing this installation.
  • Page 12 Use special tool 109-2979 to hold spindle from rotating. Do Not use the blade bolt to prevent rotation. 6. Install the UltraVac drive sheave onto the right spindle shaft. Install the washer that is supplied with the UltraVac drive kit (item 38) and the nut removed in step 5.
  • Page 13 (item 28) and whizlock nuts (item 24). Maximum in this position. Adjust the tension on the latch to deck clearance will be provided if the bolts are hold the blower up to the deck, yet allow for release installed from below the mounting pin. The mount by hand.
  • Page 14 Units Serial Number 439,999 and For Units Serial Number 439,999 and Lower: Lower with a ROPS: 1. Locate the position of the mounting holes. Clamp 1. Install four weight plates behind the front panel a weight plate to the front of the floor pan (see and two weight mounting plates (items 33 and 39) Figure 20).
  • Page 15 Installing the Removable Weights: screws, four 5/16 inch flat washers, and four 5/16-18 inch whizlock nuts (items 34, 35, and 36). Note: The removable weights are heavy. Use care when lifting them. Make sure that you can hold them securely before lifting them. Use caution when positioning your hands so that you Do Not set them down on your hands or fingers.

  • Page 16: Operation

    Figure 28 Figure 26 1. Drill the holes here 8. Slip the upper end of the tube assembly into the Assembling the Tubes hood opening. Slide the lower end of the tube assembly over the blower outlet and align the notch 1.
  • Page 17 Adjustments Note: The Ultra Vac QDS was adjusted at the factory to operate properly. However, there are three basic adjustments that can be made, should your unit require them: Figure 29 1. Handle Link 3. Stop 5. Latches 4. Hinge Links 2.