Bosch UniversalAquatak 125 Original Instructions Manual page 13

Noise/Vibration Information
Noise emission values determined according to EN 60335-2-79
Typically the A-weighted noise levels of the product are:
– Sound pressure level
– Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K determined according to EN 60335-2-79
h
– Vibration emission value a
h
– Uncertainty K
Mounting and Operation
Representation/Action Ob-
jective
Delivery Scope Univer-
salAquatak 125/130/135
Fold down handle operation
Adjusting the Handle
Connecting to the water supply
Connecting/disconnecting high
pressure gun to lance
Connecting/disconnecting high
pressure water supply hose/
nozzle
Starting
Stopping
Attaching Nozzle
Adjust water jet
Connect detergent bottle
Clean nozzle
Clean both filters
Storing the lance
Placing hose into the hose
holder
Gun/lance/nozzle stored during
work breaks
Selecting accessories
Switching on
For Your Safety
Warning: Switch off, remove plug from mains
before adjusting, cleaning or if cable is cut,
damaged or entangled.
The operating voltage is 230 V AC, 50 Hz (for non-EU coun-
tries 220 V, 240 V as applicable). If in doubt contact a quali-
fied electrician or the nearest Bosch Service Centre.
Bosch Power Tools
3 600 HA7 A..
dB(A)
dB
2
m/s
2
m/s
If you want to use an extension cable when operating your
high pressure washer, only the following cable dimensions
should be used:
Figure Page
– 2.5 mm
Note: If an extension cable is used it must be earthed and
A 218
connected through the plug to the earth cable of your supply
network in accordance with prescribed safety regulations.
B 219
If in doubt contact a qualified electrician or the nearest
C 219
Bosch Service Centre.
D 220
E 220
ded for outdoor use.
F 221
The connections (plugs and sockets) should be kept dry and
off the ground.
For increased electrical safety use a Residual Current Device
G 221
(RCD) with a tripping current of not more than 30 mA. Al-
H 222
ways check your RCD every time you use it.
If the supply cord is damaged, it must be replaced by a
I −J 223−224
Bosch Service Centre.
For products not sold in GB:
K 225
Warning: For your safety, it is required that the plug at-
tached to the product is connected with the extension cord.
L 226
The coupling of the extension cord must be protected
M 226
against splash water, be made of rubber or coated with rub-
N 227
ber. The extension cord must be used with a cable strain re-
lief.
O 227
To prevent damage to the appliance, do not allow it to oper-
ate dry.
P 228
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
Q 229
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
3 600 HA7 B..
77 73
3,0 3,0
1,3 1,5
0,6 0,6
2
– max length 25 m
WARNING: Inadequate extension cables can be
dangerous. Extension cable, plug and socket
must be of watertight construction and inten-
F 016 L81 568 | (28.11.2022)
English | 13
3 600 HA7 C..
74
3,0
1,3
0,6