Candy CH64EXCP User Instructions page 10

1) If any cook ng stage s n pos t on 0, th s d splay w ll sw tch OFF
automat cally after 10 seconds and the zone OFF sequence w ll
sound.
2) If there s res dual heat nd cat on n the d splay wh ch s OFF, "H" w ll
be d splayed.
3) Even lock funct on s act ve you can sw tch OFF a zone.
4) If only one heater s act ve and th s one s sw tched off, 4 Short beep
w ll be heard nd cat ng all cook top s Off.
Increase / Decrease power level
8
8 8
8
W th a short press on '+' or '-' keys, Increase or decrease power n the
selected zones d g t: 0-1-2-3...9-P
1. For Long Presses n + or - keys, power level ncreases /decreases
cont nuously. W th a fast ncrease, power stops at level 9, and for a
h gher power another short press s needed on the + key. No beep
sound s heard w th fast ncrease / decrease.
2. Once arr ved to P power level, press ng + key aga n does not
change power level to 0.Once arr ved to 0 power level, press ng - key
aga n does not change power level to P.
3. W th a zone ON at 0 power level, f the zone s hot, 0 w ll bl nk
alternat vely. After 10 seconds, 0 w ll d sappear an 'H' letter w ll appear
f xed on d splay.
4. When a heater s selected and '+' & '-'keys are touched at the same
t me, power level w ll go to '0' but heater w ll ma nta n selected dur ng
10 seconds. If heater was tempor zed, t mer w ll go to Off. Th s act on
can only be developed n several cases depend ng touch control
conf gurat on.The follow ng examples are for nformat on only.
Personal exper ence should then let you adapt these sett ngs to your
taste and hab ts.
Ch ld Lock
8 8 8
8
The act on w ll be done
Then, any t me when a key w ll be touched, d splays w ll show "L"
dur ng 2sec. heat ng rema ns at the same state.
To deact vate Ch ld Lock, follow the same process expla ned before.
Then Short beep w ll be heard and d splays w ll show "n" letter. Hob w ll
rema n unlocked.
Note: An automat c ch ld lock w ll produce n 15 m nutes after total
Sw tch OFF of the hob. Th s funct on w ll happens automat cally but
prev ously s necessary to program t. See User sett ngs po nt.
Double / Tr ple zones
8
8 8
8
To sw tch ON double extens on r ng, assoc ated ma n zone must be
already ON and Ind cat ng power level must be h gher than 0.
8.1- Double zone ON
1st Short Press on extens on key Sw tches ON extens on r ng. LED
over extens on key turns ON f Extens on r ng s ON.
2nd Short Press on extens on key Sw tches OFF extens on r ng.
Short beep each press on extens on key.
8.2- Tr ple zone ON
1st Short Press on extens on key Sw tches ON 1st extens on r ng. 1
LED over extens on key turns ON f 1st extens on r ng s ON (left LED
n case of tr ple zone, m ddle and only LED n case of double zone) 2nd
Short Press on extens on key Sw tches ON 2nd extens on r ng. 2
LEDs over extens on key turn ON f 1st and 2nd extens on r ngs are
ON
8
8
8
8
when lock key s touched
8
8
3rd Short Press on extens on key. Sw tches OFF 1st and 2nd
extens on r ngs.
Short beep each press on extens on key.
Br dge funct on
8 8
8
The br dge can be enabled only when both heaters are off. One heater
of the br dge has been selected, to act vate br dge funct on touch
br dge key.
A beep sounds and the zone LED s sw tched on f the zone s enabled.
Both br dge heaters w ll be selected at the same t me.
Once the heaters selected, f the power level s not the des red power
level, by the + - keys.
Both br dge heater d splays w ll show same power level.
The funct on w ll f n sh:
- If the br dge key s touched n sett ng mode
- If user selects power level "0"
Melt ng funct on
8 8
8
After a heater has been selected, to act vate melt ng funct on:
- Select melt ng key
A tone sounds and heater d splay shows "U"
The heater w ll work at power level "2"
Be ng the heater selected, Melt ng funct on w ll f n sh
- If sw tched off
- If t s selected to other power level.
Bo l ng Funct on:
8 8
8
After a heater has been selected, to act vate Bo l ng funct on:
- Select Bo l ng key
A tone sounds and heater d splay shows "P"
The heater w ll work at max mum power level for 10 m nutes.
After these 10 m nutes a tone sounds heater w ll return to level "9"
Pause function
8 8
8
The Pause funct on allows temporary paus ng of the cook ng process,
allow ng the users to answer the door or the telephone w thout worry ng
that the water s bo l ng over. Th s funct on s also useful to clean the
user nterface surface w thout chang ng the cook ng set up.
To select th s funct o , the user should touch "t mer +/- keys" together.
If the "t mer +/- keys" are touched for ½ seconds :
A beep sounds and the cooktop s stopped,
The heaters actual power sett ng s stored and all the act ve heaters
power s set to power level 0,
The heaters auto-sw ch off t me s paused,
All the t mers runn ng count downs are paused,
All keys are locked except "t mer +/- keys" and "on/off key" (T mer keys
can only be act ve f they are used together to deact vate pause
funct on),
T mer d splays noth ng, and all the heaters d splays are gett ng on and
put ng out "0", sw tch ng on segment by segment n left d rect on, and
after that sw tch ng off segment by segment n r ght d rect on,
cont nously.
09 GB
8 8
8
8 8
8
8 8
8
8 8
8