Download Print this page

Mackie Fussion Series 3000 User Manual

Mackie fussion series 3000: user guide.
Hide thumbs




   Also See for Mackie Fussion Series 3000

   Related Manuals for Mackie Fussion Series 3000

   Summary of Contents for Mackie Fussion Series 3000

  • Page 1


  • Page 2: Safety Instructions

    Mackie product. 10. Object and Liquid Entry — Care should be taken so that objects do not fall into and liquids are not spilled into this Mackie product. 11. Damage Requiring Service — This Mackie product should be serviced only by qualified service personnel when: 12.

  • Page 3: Table Of Contents

    ... 6 Don’t forget to visit our website at for more information about these and other Mackie products. ©2000 Mackie Designs Inc. All Rights Reserved. Printed in Italy. Rev. B According to OSHA, any exposure in excess of these permissible limits could result in some hearing loss.

  • Page 4: Introduction

    INTRODUCTION Thank you for choosing Mackie Designs’ active sound reinforcement speaker systems. The FUSSION 3000 is a full-range, me- dium throw, active loudspeaker system capable of extremely high sound pressure levels and wide dispersion. With almost 2000 watts of low-distortion built-in power,...

  • Page 5: Rear Panel Description

    Note: You can change the AC voltage configuration from 115V to 230V internally by reconfiguring the transformer primary wiring on the power supply board. Contact Mackie Technical Support for instructions (1-800-258-6883). FUSE Always replace the fuse with the type in- dicated on the rear panel.

  • Page 6: Main In

    MAIN IN This is a female XLR-type connector that accepts a balanced line-level signal from your mixing console or signal processor. LOOP OUT This is a male XLR-type connector that produces exactly the same signal that is connected to the MAIN IN jack. Use it to daisy-chain several FUSSION 3000s to- gether off the same signal source.

  • Page 7: Placement

    PLACEMENT The FUSSION 3000 active loudspeakers are designed to sit on the floor or to be sus- pended by the rigging points. You can stack cabinets vertically. If you do, turn the upper cabinet upside down so the high-frequency driver is closest to the high-frequency driver in the lower cabinet.

  • Page 8: Rigging

    RIGGING The FUSSION 3000 cabinets are fitted with rigging points shown in the diagram below. WARNING: Never at- tempt to suspend the FUSSION 3000 active loudspeakers by their handles. If you want to suspend them, use the rigging points only. You can suspend the FUSSION 3000 from the four fly points located on the top of the cabinet using forged shoulder eye-...

  • Page 9: Service Information

    Troubleshooting section. Doing so might save you from being deprived of your Mackie loudspeaker. Of all Mackie products returned for ser- vice (which is hardly any at all), many are coded “CND” — Could Not Duplicate— which usually means the problem lay some- where else in the system.

  • Page 10: Repair

    This is very important. When you call for the RA number, please let Tech Support know if you need new packaging. Mackie is not responsible for any damage that occurs due to non-factory packaging. 5. Include a legible note stating your name, shipping address (no P.O.

  • Page 11: Fussion 3000 Specifications

    “Mackie,” the “Running Man” figure, and “FUSSION” are trademarks or registered trade- marks of Mackie Designs Inc. All other brand names mentioned are trade- marks or registered trademarks of their respective holders, and are hereby acknowledged.

  • Page 12

    ® ™ 16220 Wood-Red Rd. NE • Woodinville, WA 98072 • USA 800/898-3211 • Outside the US: 425/487-4333 ® Mackie Designs Inc. Mackie Designs Inc. Fax: 425/487-4337 • E-mail: ®...

Comments to this Manuals

Symbols: 0
Latest comments: