Download Print this page

Mackie Fussion Series 3000 User Manual: Rear Panel Description; Ac Receptacle; Fuse; Power Switch

Mackie fussion series 3000: user guide.
Hide thumbs

Advertisement

REAR PANEL DESCRIPTION

AC Receptacle
This is where you connect the AC
linecord to provide AC power to the
FUSSION 3000's built-in power amplifiers.
Plug the linecord into an AC socket prop-
erly configured for your particular model.
The FUSSION 3000 is shipped with a
connector that mates with the AC recep-
tacle on the rear panel. Use heavy gauge
wire for the linecord to avoid power losses
across the wire. (See page 8 for more info.)
The bar
on the rear panel is there to
A
secure the linecord and prevent it from acci-
dentally getting pulled loose from the AC
receptacle. Wrap the linecord through the
bar and tie it in a knot to secure it.
Note: You can change the AC voltage
configuration from 115V to 230V internally
by reconfiguring the transformer primary
wiring on the power supply board. Contact
Mackie Technical Support for instructions
(1-800-258-6883).
FUSE
Always replace the fuse with the type in-
dicated on the rear panel. Never replace the
fuse with one of a higher value than indi-
cated on the rear panel.
115VAC Version
WARNING: Make sure
you use the correct fuse
relative to the AC operat-
ing voltage.
115VAC=16A Slow-Blow
230V AC=10A Slow-Blow
WARNING:
THIS SURFACE MAY REACH HIGH TEMPERATURE DURING
STANDARD USE. TO ENSURE PROPER OPERATION ALLOW A MINIMUM OF 6 INS.
OF CLEARANCE FROM THIS SURFACE AND ADEQUATE VENTILATION. TO REDUCE
THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THIS PANEL OR ANY ATTACHED
COMPONENT. NO OPERATOR SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
AVIS:
RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR
REPLACE WITH THE SAME TYPE FUSE AND RATING.
UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE
DEBRANCHER AVANT DE REMPLACER LE FUSIBLE
FUSSION
FS
A
POWER Switch
Switch up to turn the FUSSION 3000
on, and switch down to turn it off. Make
sure the signal source's level control is
down before you turn it on.
POWER/PROTECT Indicator
When the POWER switch is turned on,
and the linecord is connected to an active
AC Mains supply, this indicator lights green
to let you know that you're ready to rock
and roll. If one of the protection circuits in
the FUSSION 3000 should trigger, this indi-
cator changes to red. The protection circuits
include RMS limiting on the input and
thermal protection on the heatsink. If the
output begins to clip for more than a few
seconds, the POWER/PROTECT indicator
changes to red and the RMS limiting pro-
tection circuit discretely reduces the input
signal until the output is just below clip-
ping. If this should happen, turn down the
level at the source (mixing console) until
the PROTECT light changes back to green.
If the thermal protection circuit should
get activated, the POWER/PROTECT indicator
changes to red and the amplifiers shut down
until the heatsinks cool to a safe operating
level. Once the amplifier cools, the thermal
protection circuit resets and normal opera-
tion resumes. You should determine what is
causing the overheating condition and take
steps to remedy it (i.e., direct sunlight on
the heatsink, not enough clearance for air
to circulate freely around the heatsink, etc.).
PIN 1- GND / PIN 2- POS (+) /
PIN 3- NEG (-)
230VAC Version
5

Advertisement

   Also See for Mackie Fussion Series 3000

   Related Manuals for Mackie Fussion Series 3000

Comments to this Manuals

Symbols: 0
Latest comments: