Advertisement
Quick Links
Advanced RF Remote
RGB LED Controller
Model: T130(-H)
according polarity and color sequency. Please make sure the
LED rated voltage is same as the power supply and the
maximum load current is below the controller rated current.
CAUTION! The controller might be permanently
damaged if output cables short circuit. Please ensure the
cables are well insulated to each other.
3. Wiring diagram
Please connect the controller output to LED loads and
power supply to the controller power input. The output
voltage of power supply must be same as the LED load's
rated voltage. Check all cables to be well connected and
insulated before power on.
To 110/230
5-24V DC output
AC power
Power supply
5-24V DC
Wireless Remote
Ultra Compact
Wide Voltage Range
Memory Function
Overheat Protection
T130 LED
LED Loads
Controller
5-24V Driving
LED Controller
Remote
Controller
Introduction
T130 RGB LED controller is designed to drive constant
voltage LED products with common anode connection in
voltage range of DC5-24V. The receiver works with the remote
controller, user can setup RGB LED color, brightness and
dynamic modes via the remote controller.
Receiver & wiring
1
1. Power supply input
The controller supply voltage range is from DC 5V to 24V.
Please refer to the print on the controller for cable polarity.
The output voltage is at the same level as the power voltage,
please make sure the power supply voltage is correct and the
power wattage is capable for the load wattage. Please be
noted the positive power cable is directly connected to the
output cable inside the controller.
2. LED output
Connect to LED loads. Please refer to the print on the
controller for cable polarity and connect LED load with
Remote controller function
4
6
5
4. Turn ON / OFF
Press 'I' key to turn on controller or press 'O' key to turn
off. The controller will memorize the on/off status and will
restore to the previous status on the next power on. Please
use remote controller to turn on the unit if it was switched to
off status before power cut.
5. Static RGB color setting
The keys in this area set the RGB static color and
brightness. Press the colored keys to set the LEDs to
correspond color as shortcut, press 'COLOR+' and 'COLOR-'
key to select all colors from the preset library, press
and
key to adjust color brightness.
2
2
15mm
38mm
* H version picture
50mm
7
1
3
Advertisement
Related Manuals for Rayrun T130
Summary of Contents for Rayrun T130
- Page 1 Introduction Advanced RF Remote RGB LED Controller T130 RGB LED controller is designed to drive constant voltage LED products with common anode connection in voltage range of DC5-24V. The receiver works with the remote controller, user can setup RGB LED color, brightness and dynamic modes via the remote controller.
- Page 2 6. Dynamic effect setting After this operation, the LED fixture will flash quickly to acknowledge that remote pairing is accomplished. Press ‘MODE+’ and ‘MODE-’ to select dynamic effect and press ‘SPEED+’ and ‘SPEED-’ key to set the running speed of 10.
- Page 3 简介 RF⽆线遥控 LED控制器 T130RGBLED控制器⽤来驱动电压范围为5V到 24V的LED灯带或LED模块等恒压LED灯具。 ⽤⼾可以通 过卡⽚式射频控制器来调节LED灯具的颜⾊、 亮度和动 态模式。 控制器需要直流电源供电， 并根据接收到的遥 型号:T130 （-H） 控器指令驱动LED灯具， 实现颜⾊、 亮度和动态模式调 节功能。 主机和接线 无线遥控 小尺寸 15mm 38mm * -H版本图⽚ 50mm 宽压输出 1.电源输⼊ 控制器可接受电压为5V到24V的直流电源供电。 请按 照控制器上标明的电源极性进⾏连接。 控制器的输出电 记忆功能 平与电源输⼊电压相同， 请确保LED灯具额定电压与电 源相同， 且电源的功率满⾜控制器和灯具的需求。 过热保护 功能 2.LED输出...
- Page 4 6.RGB动态调节 10.保留当前遥控器并清除其他遥控器 按和可以选择动态模式， 按键和键 在控制器已与多个遥控器配对， ⽽仅想保留当前遥 MODE MODE 可以调节动态模式的运⾏速度。 控器的情况下， 可以将正在使⽤的遥控器与控制器再进 按键激活动态演⽰模式， 控制器将按每个动态 ⾏⼀次配对操作， 此后控制器将清除其他已配对的遥控 模式将重复3次的⽅式循环演⽰动态效果。 器⽽仅保留当前使⽤的遥控器。 过热保护 7.遥控器指⽰灯 按下遥控器按键时， 该指⽰灯会快速闪烁。 如果指⽰ 本机具有过热保护功能， 可防⽌控制器因负载过重 灯慢闪， 则说明遥控器电池电量已耗尽， 请更换遥控器 引起异常发热⽽导致损坏。 过热保护时控制器将关断输 电池 （CR2032型纽扣电池） 。 出， 当温度下降到安全范围时， 将尝试恢复正常⼯作。 过 操作⽅法 热保护功能仅能在⼀定程度上防⽌控制器损坏， 为确保 安全， 请勿将控制器输出过载或短路。 8.使⽤遥控器...