Dometic RM4601 Installation & Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Dometic Manuals
  4. Automobile Accessories
  5. RM 4601
  6. Installation & operating instructions manual

Dometic RM4601 Installation & Operating Instructions Manual

Hide thumbs Also See for RM4601:
Table of Contents

Advertisement

Quick Links

Download this manual
FOR YOUR SAFETY
If you smell gas:
1. Open windows and door.
2. Don't touch electrical switches.
3. Extinguish any open flame.
4. Immediately call your gas supplier.
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
Improper installation, adjustment, alteration,
service or maintenance can cause injury or
property damage. Refer to this manual. For
assistance or additional information consult a
qualified installer, service agency or the gas
supplier.
If the refrigerator stops cooling - or - if
it emits an ammonia smell, immediate-
ly turn the refrigerator off and contact a
Service Center.
REVISION A
Form No. 3313941.000 09/16
INSTALLATION
&
OPERATING
INSTRUCTIONS
RM4601

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RM4601 and is the answer not in the manual?

Questions and answers

Related Manuals for Dometic RM4601

Summary of Contents for Dometic RM4601

  • Page 1 If the refrigerator stops cooling - or - if it emits an ammonia smell, immediate- ly turn the refrigerator off and contact a RM4601 Service Center. REVISION A Form No. 3313941.000 09/16...

  • Page 2: Table Of Contents

    The right gas consumption is ....1.7 MJ/h APPENDIX A - WIRING DIAGRAM ... . 12 The data plate contains e. g. the following details: Model designation RM4601 Product number ........

  • Page 3: Operating Instructions

    OPERATING INSTRUCTIONS SYMBOLS The following symbols are used throughout this manual: CONTROLS This is the safety alert symbol. It is used to alert you to personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious...

  • Page 4: 230-240V Operation

    USING THE REFRIGERATOR 4. Press button (D) all the way in and hold, press button (C) for the piezo igniter several times to light the burner. This can be observed on the flame indicator (B), on the refrigerator. When the flame is on, the red indicator is in the green field.

  • Page 5: Airing Position Card

    AIRING POSITION CARD The exterior of the refrigerator should be wiped clean now and then, using a damp cloth and a small quantity of de- tergent. But not the door gasket, which should only be Use the Airing Position Card cleaned with soap and water and then thoroughly dried.

  • Page 6: Maintenance

    Exhaust gases must be vented through the wall to the outside of the vehicle. Dometic wall venting SERVICE AND SPARE PARTS systems provide provision for venting the exhaust gases.

  • Page 7: Technical Data

    Height......1415 mm passage using one of the OPTIONAL Dometic ventila- Width ......607 mm tion systems.

  • Page 8: Building-In

    BUILDING-IN SECURING THE REFRIGERATOR The refrigerator must not be exposed to radiated heat For the best cooling performance the installer must block from hot objects. any space between the counter, storage area or ceiling It is not a good practice to install the refrigerator so that and top of the refrigerator greater than 40 mm.

  • Page 9: Drain Water Hose

    3. One screw installed in the rear base, see fig. The supply pipe should preferable be of copper. If any oth- 9. The screw shown on the burner side is an er material is used, it must be of a type approved for use with continuously operating bottled-gas appliances and option.

  • Page 10: Mounting Instructions

    Before leaving Once the installation is complete, test the operation of the refrigerator and instruct the user on its correct operation. If the appliance fails to operate correctly, contact your lo- cal Dometic Service provider.

  • Page 11: Removing And Replacing The Shelves

    REMOVING AND REPLACING THE SHELVES 1. Remove the shelf locks by inserting the tip of a flat bladed screwdriver into the slot of the locks. Turn the screwdriver counterclockwise and then remove the shelf locks from the wire shelf. 2. Tilt the shelf to one side at an angle while pul- ling forward.

  • Page 12: Appendix A - Wiring Diagram

    APPENDIX A - WIRING DIAGRAM...

Table of Contents