Advertisement
Parameter 1
Display
Description Default value
Average
delay count
Peak auto
detect Hold
Lock
Parameter 2
Display
Description Default value
High Peak
-
Display
Low Peak
-
Display
Output
High Set
Output
Low Set
Output Type
Select
HYS terisis
comparative output action ( )
Operation
Output Operation
mode
It does not operate under the initial
How to set up the parameter
▒ Parameter1 ( Key - keep pushing the button(min 2 sec))
keep pushing
key(min 2 sec) and find the parameter 1 set up mode
Key
set up start
Default value :
1. Display the number
of average
Key
Key
set up start
2. Automatically holding
Default value :
at the max mesurement
Key
Key
set up start
3. Set up the lock
Default value :
function
Key
※
,
display is optional.
Set range
Remark
Max :
set up the number of input
for average measurement.
Min :
set up automatic holding
when peak value measures.
set up lock fuction.
Set range
Remark
Display the max value
-
among the measured values.
Display the min value among
-
the measured values.
Max :
Set up the high set value.
Min :
Max :
Set up the low set value.
Min :
LL :
HH :
Set the comparative output
LH :
mode.
HL :
IL :
Max :
Set up the hysteresis.
Min :
Explanation
H : Hysteresis
No output operation
Current indication value ≦
LO output becomes ON.
Current indication value ≧
GO output becomes ON.
Current indication value ≧
HI output becomes ON.
Current indication value ≦
GO output becomes ON.
Current indication value ≦
LO output becomes ON.
Current indication value ≧
HI output becomes ON.
Current indication value ≺
GO output becomes ON.
Current indication value ≧
LO output becomes ON.
Current indication value ≧
HI output becomes ON.
Current indication value ≺
, GO output becomes ON.
Same as the
operation but LO output will
not operate under the initial setup value of
It starts to operate from the next value of
Key
set up
Key
completed
25 (max. value)
set up
1 (min. value)
Key
set up
completed
Key
OFF
H - Hd
L - Hd
set up
Key
set up
Key
completed
OFF ON
set up
▒ Parameter2 ( Key -shortly push the button (below 2 sec)
Display function of
the max input value
Key
Display function of
the min input value
Key
Set up the max
comparative output
value
Key
Set up the min
comparative output
value
Key
Set the comparative
output mode
Key
Hysteresis Selection
▒ Lock key ( Key - keep pushing the button(min 2 sec))
Key
※ every parameter set up is not available when the
▒ How to change the parameter set value
Set value :
1. Pressing
key more than 2 sec within the RUN MODE will enter into the Parameter 1 and
pressing
key less than 2 sec will enter into the parameter 2.
2. Able to select the parameter by pressing
Set value :
parameter and set value repeatedly flickers in the display unit.
3. Able to change the set value by pressing the
in the display unit(when set value is 0, only the 0th digit of constant value flickers and displayed)
When changing the setting of constant value, able to perform the position shifting by using
Set value :
Example)
value,
When set value is constant, only 0th digit of the constant value will flicker in the display unit.
value,
In order to change the value on 100th digit, press the
the
key, position of the digit will shirt to the left and selected digit will flicker in the display unit.
value,
When setting is completed, return to the parameter mode by pressing the
value,
flickers the parameter and set value repeatedly. Able to return to the RUN mode by pressing the
key again.
value,
Initializing set value
value,
,
Push the button
And then
is displayed. When displaying
value,
default value is initialized.
value,
(* Initializing set value is not available when
Error display code
and
: Displayed when measuring input electrical pressure ecxeeds max input range.
.
: Displayed when measuring input electrical volatge ecxeeds max input range.
.
: Displayed when high comparative output set value is lower than low
comparative output set value.
▒ Retransmission output regarding the power factor display
▒ Retransmission fucntion (Auxiliary Output)
E - Hd
● Current output
Generate 4 - 20 mA d.c for a present displayed value (resolving power 2000)
● Relay output (250 V a.c 5 A below) 1a × 3
※ Caution) PF3 is a power factor meter based on the cycle measurement method.
It might be possible to be late input(max 2 sec) or not accurate when use in
below 5% of the rated voltage.
4
shortly push the
button(below 2 sec) and find the parameter 2 set up mode
Key
max.
Display of the max
completed
input value
value default
Key
Display of the min
min.
completed
input value
value default
Key
Key
set up the max
set up start
set up
completed
comparative output value
To move the position of the
number then press
Key
Key
set up the min
set up start
completed
set up
comparative output value
To move the position of the
number then press
Key
set up start
Set the comparative
Key
completed
output mode
set up
Key
Key
set up start
set up
completed
Default value : 01
To move the position of the
number then press
Key - keep pushing the button(min 2 sec)
Key
set up
Key - keep pushing the button(min 2 sec)
completed
Key
Default value :
Key
set up
set up
Key
completed
Default value :
Default value :
Key
set up start
Default value :
Key로
Set value :
설정값 변경
Key
set up start
Set value :
Set value :
Key
,
key and within the selected parameter,
set up start
Key로
Set value :
설정값 변경
Key
set up start
key and at this moment, set value flickers
Set value :
Set value :
Key
set up start
Key
Set value :
set up
Key
set up start
Set value :
Set value :
key 3 times. Each time when users press
sequancely with pushing the
, push again the
on.)
Key
set up
Key
set up
Key
set up
9.999 (set up the max comparative output value)
-1.999 (set up the mix comparative output value)
key
Key
set up
9.999 (set up the max comparative output value)
-1.999 (set up the mix comparative output value)
key
Key
set up
LL.ot
HH.ot
LH.ot
HL.ot
IL.ot
Key
set up
99 (max. value)
00 (min. value)
key
Key
set up
OFF
ON
completed
Key
set up
Key
OFF
ON
completed
set up
on.
Key로
설정값 변경
Key로
설정값 변경
key.
Key
set up
key. At this moment,
.
button and the all
Advertisement
