Lorex LH310 Quick Setup Manual

LH310
Series Edge DVR
Quick Setup Guide
Network Ready, H.264 High Performance Digtial Video
Surveillance Recorder
PACKAGE CONTENTS:
1 x EDGE DIGITAL VIDEO RECORDER WITH PRE-INSTALLED HDD*
1 x USB MOUSE
1 x POWER ADAPTOR
1 x DVI/VGA ADAPTOR (8/16-channel only)
1 x FLEX IR EXTENDER
Easily Connects
1 x REMOTE CONTROL**
to a Monitor with a
1 x ETHERNET CABLE
DVI/VGA Input.
1 x MOUNTING KIT
1 x INSTRUCTION MANUAL HDMI Compatible*
1 x QUICK START GUIDE
1 x DOCUMENTATION CD
DVI TO HDMI CONVERTER CABLE REQUIRED. (NOT INCLUDED)
ATTENTION:
• * Channel/ Port configuration and HDD (hard disk drive) capacity may
vary by model. Check your package for specific content information.
• **Remote control included with the system may vary depending on model.
• Monitor and Cameras are not included.
• Broadband Router and Computer are required for local and
remote monitoring (not included).
• For detailed setup and software information, please refer to
your printed User's manual (included).
It's all on the Web
www.lorexcctv.com
For detailed setup
information, please
refer to your included
User's Manual. For
additional information,
please visit our website
www.lorexcctv.com
Information in this document is subject to change without notice. As our products are subject
to continuous improvement, Lorex Technology INC. and our subsidiaries reserve the right to
modify product design, specifications and prices, without notice and without incurring any
obligation. E&OE © 2009 LOREX. All rights reserved.
Time
BASIC SETUP
under 15 minutes under 30 minutes under 60 minutes
Time
Hand Tools Hardware
BASIC INSTALLATION GUI DE
Router
under 15 minutes under 30 minutes under 60 minutes over 60 minutes
Time: 20 Minutes Hand Tools Skills - Easy
STEP 1
Skill Level
Hand Tools Hardware Hi Speed
Router
easy Intermediate
Skill Level
The LH310 Series Edge DVR is designed to mount securely
to the back of LCD monitors with a VESA mount. However, if
Intermediate advanced
desired, you can also leave the DVR in a standard horizontal easy
position.
ATTENTION: YOU CAN ONLY MOUNT THE EDGE DVR TO AN
LCD MONITOR WITH A VESA MOUNT AND AN INDEPENDENT
STAND.
Mounting the Edge DVR
Screw the provided
1
mounting screws
into the two top
holes in the rear
Powering ON the Edge DVR
panel of your LCD
monitor. Make sure
the screws are only
3/4 of the way in; this
will allow sufficient
clearance to hang
the Edge DVR.
Carefully place the Edge DVR
2
(front panel facing up) over the
screws and slide down into
place.
Managing Passwords
Connecting the Ethernet Cable
Connect one end of the Ethernet
3
cable (for remote monitoring) to
one of the router's (not included)
LAN ports and the other end to
the DVR's Network Port.
Connecting the USB Mouse
Connect a USB mouse to the
4
USB port on the rear panel of
the Edge DVR.
Setting the Date & Time
10
Connecting the Cameras
(not included)
Connect BNC cameras to the BNC
5
ports on the rear panel.
Time
BASIC SETUP
over 60 minutes under 15 minutes under 30 minutes under 60 minutes
Time
Hi Speed Hand Tools Hardware
BASI C I NSTA L LATIO N GU IDE
Router
under 15 minutes under 30 minutes under 60 minutes over 60 minutes
Time: 20 Minutes Hand Tools Skills - Easy
STEP 1
Skill Level
Hand Tools Hardware Hi Speed
CONTINUED
Router
advanced easy Intermediate
Skill Level
Connecting a Monitor
(not included)
Connect the VGA / DVI cable (not included)
6 Intermediate advanced
easy
from your LCD monitor to the VGA port (4
CH) / DVI port (8/16 CH only) on the rear
panel of the system.
Connecting the Flex-IR Extender
Connect the Flex-IR extender to the
7
port on the rear panel of the DVR.
Position the Flex-IR extender near the
front of your monitor, or where it will
receive a clear signal from the remote
control.
Connect the power cable to the
8
DC 12V port on the rear panel of
the DVR. At startup, the system
performs a basic system check and
runs an initial loading sequence.
After a few moments, the system
loads a live display view.
*NOTE: Make sure all cameras and
cables are properly connected prior to
powering on the system.
The system has the following user authorities:
9
• ID 1—normal user: Has full control of the system, but cannot
change passwords or enable/disable password checking.
Default password: 1111
• ID 2—administrator: Has full control of the system but can
change both administrator and user passwords and enable/
disable password checking. Default password: 2222
By default, when you first startup your system, you will be
logged in as ID 2
.
1. Click to open the Main Menu.
2. Click to open the Setup menu.
3. Click Date/Time Setup and configure the following options:
• Date Mode: Use the scroll wheel to select Y/M/D, D/M/Y, or
M/Y/D.
• Date: Use the scroll wheel to manually enter the date.
• Time: Use the scroll wheel to manually enter the time.
4. Click Exit/Update. The new date and time are saved; the
system returns to the Setup menu.
5. Right click to exit until all menus are closed. The date
and time will appear on the bottom-left corner of the screen.
Time
NAVIGATION AND CONTROLS
over 60 minutes under 15 minutes under 30 minutes under 60 minutes over 60 minutes
Hi Speed Hand Tools Hardware Hi Speed
BAS IC IN S TALL ATI ON GU IDE
Router
Time: 20 Minutes Skills - Easy
STEP 2
Skill Level
advanced easy Intermediate advanced
Using the Main Menu
This step relates to remote viewing over the LAN (local area network)
by using a pc located on the same network as that of the DVR.
1 2 3
1
Press the button on the remote
control to open the Main Menu.
1. Camera, 2. Setup, 3. Record, 4. Alarm
5. Backup, 6. LAN
TIP: When navigating menus: Left
4 5 6
mouse button: Click to select menu
options. Scroll-Wheel: Scroll up/down
to change values for selected options.
Using the Remote Control**
1. MENU: Opens the system main menu.
2
2. : Press to open the Split-Screen
Selection menu (8 / 16-channel only).
1 2
From full-screen single channel view,
3
changes display view to Quad
4
5
split-screen (4-channel model only).
7 6
3. /CH+: Move cursor in menus up;
9 8
Channel Up.
11
10
4. /FWD: Move cursor in menus right;
12
during playback, increase forward 13
playback speed (5X, 15X, 60X).
14
5. /REW: Move cursor in menus left;
during playback, increase reverse
playback speed (5X, 15X, 60X)
6.  / II: Start/pause forward playback.
7. /CH-: Move cursor in menus down;
Channel down.
8. :Confirm menu selections.
9. ESC: Go back / exit menus.
10. OSD: Show/hide the on-screen display.
11. LIST: Open the Event List menu.
12. : While in Event List menu, press to
delete a selected event (no confirm or
undo).
13. : Decrease value of selected menu
option.
14. : Increase value of selected menu
option.
**Remote control included with the system
may vary depending on model.
Using a Mouse
• Left-Button: Click to select a menu option; 3
3
while in Quad mode (Live View or 1
2
Playback), click on channels 1, 2, 3, or 4 to
view the selected channel in full-screen.
• Right-Button: Click to return to previous
menu; exit menus/modes.
• Scroll-Wheel: Scroll up/down to change
values in selected menu options; position
markers in playback bar.
Congratulations! You have completed
STEP 1 & 2 successfully. Your DVR is now
ready to use. Refer to the owner's manual
to learn how to record, playback, use the
search features and all other features
available with this DVR.
Time
SET-UP LOCAL VIEWING ON YOUR PC
under 15 minutes under 30 minutes under 60 minutes over 60 minutes
Time
Hand Tools Hardware Hi Speed
LOCAL VIEWI N G I N STA LLATIO N GUI DE
Time: 30 Minutes Hardware Skills - Intermediate
STEP 3 Router
under 15 minutes under 30 minutes under 60 minutes over 60 minutes
PC/Router
Skill Level
Hand Tools Hardware
Hi Speed
easy Intermediate advanced
Router
Skill Level
easy Intermediate advanced
Retrieve the DVR Information
NOTE: It might be necessary to change the IP address of the DVR to
match the IP address of your local network. For more details, please
see Appendix B: Setting up Local and Remote Viewing in the LH310
Instruction Manual.
1 1.Press the button twice on the remote control.
OR
1. From the main Menu, click , and then click Information.
Your IP address and MAC address are under LAN.
2. To exit, right-click or click until you return to the main screen.
Record the IP and MAC Addresses in the section below:
IP ADDRESS : . . .
MAC ADDRESS : : : : : :
(Required for DDNS registration)
Getting Started :
(on your local computer)
Before using DVR Netviewer, you must configure settings in
2
QuickTime® (4-channel only). QuickTime is required for DVR
Netviewer to function properly. If not already installed on your
system, download QuickTime from www.apple.com/quicktime
Configuring QuickTime :
(on your local computer)
3 You must configure QuickTime prior to using DVR Netviewer for the
first time (4-channel only).
To configure QuickTime:
1. With QuickTime installed on your system, open QuickTime
by double-clicking the QuickTime icon on your desktop or
selecting Start>Programs>QuickTime>QuickTime Player.
2. From the QuickTime Player main window, select Edit>
Preferences>QuickTime Preferences.
3. From the QuickTime Preferences window, click the Advanced
tab.
4. Under Transport Setup, select Custom. The Streaming
Transport window opens.
5. Under Transport Protocol, select HTTP.
6. Under Port ID, select 80 and click OK. The Streaming
Transport window closes.
7. From the Preferences window, click Apply, and then click OK.
LH310 Series Quick Setup Guide - English - R1