Subscribe to Our Youtube Channel
Related Manuals for Logic Controls CR3000
Summary of Contents for Logic Controls CR3000
- Page 1 Model: CR3000 Series Compact Cash Drawers Compact, with Small Footprint USER MANUAL...
-
Page 2: Fcc Notice
NOTICE The manufacturer of the POS cash drawer makes no representations or warranties, either expressed or implied, by or with respect to anything in this manual, and shall not be liable for any implied warranties of fitness for a particular purpose or for any indirect, special or consequential damages. -
Page 3: Table Of Contents
TABLE OF CONTENTS FEATURES ... 1 CARTON CONTENTS ... 2 INTERFACE DESCRIPTION ... 2 INSTALLATION ... 3 FUNCTIONAL TEST ... 4 KEY LOCK OPERATION ... 6 SPECIFICATIONS ... 7 CONNECTOR PIN OUT ... 8 CONTROLLER BOARD JUMPERS ... 10... -
Page 4: Features
FEATURES • Low cost • Small foot-print with efficient use of internal space • Drawer opens from any POS printer drive circuit • Bill and coin compartments • Three-position lock for maximum cash security • High security - no screws on the outside of the case •... -
Page 5: Carton Contents
3. Two keys 4. User’s manual INTERFACE DESCRIPTION Model CR3000 - Printer Driven Interface: Connect the drawer to the POS printer as shown in Figure 1. Whenever the POS application software sends a drawer open command to the POS printer, the printer will output an electrical pulse to open the drawer. -
Page 6: Installation
Connect the drawer to the computer as shown in Figure 3. Connect the power adapter output to the power input jack. Whenever the POS application software transmits the pre-set security code to the computer’s parallel (LPT1) port, the drawer will open. -
Page 7: Functional Test
The actual key entries are enclosed within quotation marks (“ “). Do not type the quotation marks as part of your entry. Model CR3000, CR3001 with dedicated interface: 1. From the C prompt type “MODE COM1 96,N,8,2” and press ENTER. - Page 8 MODEL CR3001 with non-dedicated interface 1. From the C prompt type “MODE COM1 96,N,8,2” and press ENTER. 2. Type “TYPE CON>COM1” and press ENTER. 3. TYPE “^G” and press ENTER. The cash drawer will open if the security code is 07 Hex as set by the manufacturer. NOTE:If another security code has been selected to open the cash drawer then the corresponding ASCII character must be substituted to open the drawer.
-
Page 9: Key Lock Operation
The cash drawer is manually opened when the lock is in the full clockwise position. Model CR3000, CR3001 Keylock Operation: :Drawer securely locked. Can not be opened by computer, printer, or manually. -
Page 10: Specifications
Weight 14.3 lb. Height 3.3 in. Width 15.7 in. Depth 16.1 in. ELECTRICAL: INPUT TO SOLENOID (CR3000, CR3001) Pulse Amplitude Pulse Width Pulse Duty Cycle Peak Current POWER ADAPTER (CR3001) Input Voltage SERIAL INPUT (CR3001) Data Format Protocol (see Fig. 4) -
Page 11: Connector Pin Out
CONNECTOR PIN OUT Figure 5 will show the connector arrangement for the CR3001 cash drawer. The following charts will show the function of each pin. P1 (DB25 M) - Parallel Input From Computer Pin # Function -Strobe Data 0 Data 1 Data 2 Data 3 Data 4... - Page 12 No connection No connection No connection 12-17 No connection POS printer interface; paired with pin 25 No connection DTR, Data Terminal Ready; from computer (tied to pins 6 & 8) 21-24 No connection POS printer interface, paired with pin 18...
-
Page 13: Controller Board Jumpers
P6 (DB9M) - Serial Input from computer Pin # Function DCD, tied to pins 4 & 6 Transmit data to computer Receive data from computer DTR, tied to pins 1 & 6 Ground DSR, tied to pins 1 & 4 RTS, tied to pin 8 CTS, tied to pin 7 No connection...
Need help?
Do you have a question about the CR3000 and is the answer not in the manual?
Questions and answers