Page 1
User Manual Model: NG-RV1100 Version: 1.0 English Due to the regular upgrades of systems and products, NGTeco could not guarantee exact consistency between the actual product and the written information in this manual.
Important Notes When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE) WARNING -To reduce the risk of fire, electric shock, or injury: 1) Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing.
Page 4
18) Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury. 19) Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion.
What’s in the Box Sweeping Robot X1 Charger X1 Adapter X1 Dust Box X1 Brash in left X2 HEPA and Filter Sponge X1 Brush in right X2 Quick Start Guide Quick Start Guide X1...
Product Overview 1. Top View ON/OFF/Clean/Pause Short - Press to start clean/pause cleaning. - Press and hold for 3 seconds to power ON. - Press and hold for 8 seconds to power OFF. Recharge Key/Fixed-point Cleaning/Pause - Short press to recharge/pause recharge. - Press and hold for 3 seconds to clean up as required.
Other Accessories 1. Dust Box Filter Gauze Dust Box Button Note: 1. Please rinse with clean water, do not add any detergent. 2. Do not use a brush or fingers to clean the Filter filter. 3. Air-dry the filter for at least 24 hours and dry thoroughly.
Page 8
3. Keys and Indicators - Press to start clean/pause cleaning 1) ON/OFF/Clean/Pause Short - Press and hold for 3 seconds to power ON - Press and hold for 8 seconds to power OFF 2) Recharge Key/Fixed-Point - Short press to recharge/pause recharge. - Press and hold for 3 seconds to clean up Cleaning/Pause as required.
Map Management Automatic Cleaning Press the button on the main unit, or use Mobile APP to perform automatic cleaning mode. Edge Cleaning You can use the Mobile APP to clean along the edge. The machine will immediately move to the right and along the wall to clean after encountering an obstacle.
Installation Steps When using the robot for the first time, keep an eye on the robot to see if any problems occur. 1. Remove the power cords and small objects from the floor that may entangle robot. 2. Robot may climb on top of objects less than 0.59in. /15mm in height. Remove these objects if possible.
Page 11
Installation Steps 1. Connect the power cord, and then put the excess wire into the wire box. 2. Place the charging stand against a wall on a flat floor, and then connect power. Note: - Make sure there is a space of more than 0.5 meters on both sides and more than 1.6ft/0.5m 1.5 meters in front.
Instructions for Use 1. Power Switch: 1) Turn “ON”, after flashing white light, will hear ” POWER ON”, and then it works. 2) Turn “OFF“, cut off the power supply, which mean it's shutdown completely. 2. ON/OFF key (Note: Turn power switch to "ON" to turn on the power status): 1) In the power-off...
Connecting to NGTeco Home App Step 1: Download the App and Register Your Account Search for the NGTeco Home App in Apple App Store or Google Play Store and download the App to your mobile phone. Open the NGTeco Home App and log in with your account. If you do not have an account, create an account with your phone number or Email ID.
Routing Maintenance Roller Brush Brush Inside 1. Turn the machine over and press the buckle 1. Turn the machine over and pull out the side on the brush cover to take out the brush. brush vertically. 2. Use the matching cleaning tool to remove 2.
Page 15
Routing Maintenance Sensors (Regular cleaning is Anti-drop Sensor recommended) Charging Spot Wipe the various sensors on the machine with a soft and dry cloth, including: 1. Along the wall sensor on the right side of the main unit. 2. Three anti-drop sensors at the bottom of the main unit.
Basic Information Device Robot Vacuum Name Type NG-RV1100 Size 327*325*76mm Weight 2.8kg Battery 2600mAh-Lin Rated voltage 14.4V Rated power Charging Base NG-RV1 Type Size 160*145*90mm Rated voltage 11.4W Rated power 11.4W...
Questions Solution -The battery is low, please place the device on the charging stand and align the charging pads, and the device will automatically turn ON Cannot boot (when it is completely dead, it will take a while to automatically turn on). -When the ambient temperature is lower than 0°C and higher than 40°C, please use it in the environment of 0°C to 40°C.
Troubleshoot Solution Fault Tone Mistake 1: Dustbin removed, please The cleaning is triggered when the dust box is taken out, check and restart please put the dust box back in. The cleaning is triggered when the water tank is removed, Mistake 2: Water tanks removed please put the water tank back in.
Product Hazardous Substance Content and Name Harmful Substances Name (Pb) (PBDE) (Hg) (Cr(VI)d) (PBB) (Cd) Circuit Board Assembly Battery Charger Power Cable Metallic Parts Motor Shell Other Accessories This form is prepared according to the provisions of SJ / T 11364 O: Indicates that the content of this hazardous substance in all homogeneous materials of this part is below the limit requirement specified in GBT/T 26572 X: Indicates that the content of the hazardous substance in at least one homogeneous...
Page 20
FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Page 21
FCC Statement (Cont.) IC warning: This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.