Roborock S5 MAX Manual

Product introduction

Robot

On/Off

• Press to start cleaning
• Press and hold to power on or off

Power indicator

• White: Battery level ≥ 20%
• Red: Battery level < 20%
• Flashing: Charging or starting up
• Flashing red: Error

Dock/Spot Clean

• Press to return to the dock
• Press and hold to spot clean
  Note:
  Press any button to pause cleaning, returning to dock, or spot cleaning.

Parts list

Charging dock

Moisture-proof mat

Power cable

Mop cloth mount

Mop cloth

Dustbin

WiFi indicator light

• Off: WiFi disabled
• Slow flashing: Waiting for connection
• Fast flashing: Connecting
• Steady: WiFi connected

Machine and sensors

Mopping module

Charging dock

Installation

Using the robot

1. Place the charging dock against the wall on a flat surface and plug it into the mains power.
   
   Note:
   • The charging dock should have more than 0.5m (1.6ft) of clearance on each side, and more than 1.5m (5ft) in the front.
   • If the power cable is vertical to the ground, it may be caught by the machine, causing the charging dock to be disconnected.
   • The charging dock indicator is on when the charging dock is electrified, and off when the robot is charging.
2. Secure the charging dock with the adhesive tape.
   Wipe the floor of the area where the charging dock will be placed with a dry cloth, then stick the enclosed double-sided tape to the floor. Place the dock onto the double-sided tape to secure it in place.
   
   Note:
   • Use of the double-sided tape to secure the charging dock is optional.
   • When necessary, remove the double-sided adhesive tape slowly to reduce residue glue.
3. Secure the moisture-proof mat.
   After securing the charging dock, wipe the area where the moisture-proof mat will be placed with a dry cloth as shown. Stick the double-sided tape first to the moisture-proof mat then in position on the floor.
   
   Note:
   Always place the moisture-proof mat on a wooden floor
4. Power on and charge.
   Press and hold the button to turn on the robot. When the power indicator lights up, place the robot onto the charging dock to begin charging. The robot uses a high-performance lithium-ion rechargeable battery. To maintain peak battery performance, always keep the robot charged.
   
   The color of the power indicator indicates the battery level.
   • White: ≥ 20%
   • Red: < 20%
     Note:
     The robot will not turn on when the battery is low. Place the robot directly onto the charging dock to begin charging.

Connect to the app

5. Connect to the app.(recommended)
   1. Download the Roborock app or Xiaomi home app
      1. Search "Roborock" in the App Store or Google Play, Or scan the QR code below, then download and install the app.

1. Search "Xiaomi home" in the App Store or Google Play, Or scan the QR code below, then download and install the app.
   
   
   
   
   1. Reset WiFi
      1. Open the top cover of the robot to reveal the WiFi indicator light.
      2. Press and hold the button and the button until you hear the "Reset WiFi" voice alert. When the WiFi indicator light is flashing slowly, the robot has entered network configuration mode.
         Note:
         If you cannot connect your phone to the robot, reset the WiFi, and add your robot as a new device.
   2. Add device
      Open the app and click "+" in the top right corner, then follow the instructions in-app. Once your robot has been added, it will be found in a list on the homepage.
      Note:
      • Due to ongoing app development, the actual process may differ slightly from the above description. Always follow the instructions given in the app.
      • Only 2.4GHz WiFi is supported.
        
        WiFi indicator light
      • Off: WiFi disabled
      • Slow flashing: Waiting for connection
      • Fast flashing: Connecting
      • Steady: WiFi connected

Using the robot

6. Mopping
   Note:
   It is recommended that all floors are vacuumed at least three times before the first mopping session to reduce excessive dirt buildup on the mop.
   1. Remove the water tank
      Press down the water tank latch and slide the tank backwards to remove it.
      
      
   2. Fill the water tank
      Open the water tank, fill it with water, and close it tightly.
      
      Note:
      Do not use hot water, which may cause the tank to deform. To prevent corrosion or damage, do not use cleaning fluid or disinfectant in the water tank.
   3. Install the water tank
      Slide the water tank into the robot until you hear it lock with a click.
      
      
   4. Install the mop cloth
      If mopping immediately, dampen the mop cloth and squeeze it dry then attach it to the mop cloth bracket.
      
      Note:
      Use a barrier tape or no-mop zones to separate prevent mopping on carpeted floors.
   5. Attach the mop cloth bracket
      Slide the mop cloth bracket under the water tank following the alignment marks, until you hear a click.
      
      Note:
      Cleaning the mop cloth after 60-minutes of mopping is recommended to ensure water flow and cleaning quality.
7. Adjust water flow rate
   Use the mobile app to adjust the water flow as required.
   
   
8. Start cleaning
   When the battery is fully charged, the power indicator will remain lit. Press the button or use the app to start cleanup.
9. Remove the mop cloth bracket
   To remove the mop cloth bracket, press the two clips inwards and pull the bracket backwards.
   
   Note:
   • When the charging dock is placed on a wooden floor, always use it with the moisture-proof mat to prevent moisture damage.
   • Removing and washing the mop cloth bracket, and emptying the water tank frequently is recommended to prevent odors or mildew.
   • Remove the mop cloth bracket if not mopping.
10. Separating the water tank from the mop cloth bracket
    As shown in the figure, press the two side clips inwards and slide the mop cloth bracket backwards to separate it from the water tank.
    

On/Off

Press and hold the button to turn on the robot. The power indicator will turn on and the robot will enter Standby mode. If the robot is in Sleep mode, press and hold the button to turn it off and end the current cleanup.

Note: The robot cannot be turned off when it is charging.

Start cleanup

Press the button to start cleaning. Once started, the robot will plan its cleaning route based on its scan of the area. It cleans along the edges of a zone first and then moves in a Z-shaped cleaning route to cover the internal area efficiently and thoroughly.

Note:

• Cleaning cannot start if the battery level is too low. Allow the robot to charge before restarting cleanup.
• Tidy away any cables on the ground (including the power cable of the charging dock) before cleaning to avoid losing power or damaging either the robot or the connected device.
• If a cleanup finishes within 10 minutes, cleaning repeats by default
• If the battery runs low before cleanup is complete, the robot will carry out a top-up charge before resuming cleanup from where it left off.

Pause

When the robot is cleaning, press any button to pause it.

Then press the button to continue cleaning or the button to return it to the charging dock and stop the cleaning cycle.

Note: Placing a paused robot on the charging dock manually will end the current cleanup.

Sleep

If the robot is paused for over 10-minutes, it will go to sleep, and its power indicator will flash slowly. Press any button to wake it back up.

Note:

• The robot will not go to sleep when it is on the charging dock.
• The robot will automatically shut down if left in sleep mode for more than hours.

Charging

Auto: After cleaning, the robot will automatically return to the charging dock to recharge.
Manual: In Pause mode, press the button to send the robot back to the charging dock.
The power indicator will flash slowly as the robot charges.

Note: If the cleaning cycle was started away from the charging dock and the robot could not return to the dock after cleaning, it will instead return to its starting point. Place the robot directly on the dock to recharge it.

Error

If an error occurs while the robot is cleaning, the power indi-cator will flash red quickly, and you will hear a voice alert. See "Troubleshooting" for resolution options.

Note:

• The robot will go to sleep automatically if left in an Error state for over 10-minutes.
• Placing the robot on the charging dock in an error state will stop the current cleanup.

Reset WiFi

If your phone cannot connect to the robot because you have changed your router configuration, forgotten your password, or any other reason, open the top cover to see the WiFi indi-cator light then press and hold the button and the button until you hear the" Resetting WiFi" voice alert. When the WiFi indicator light flashes slowly, reset is complete.

Note: If the robot is left connecting to the network for over an hour, its WiFi will be disabled. Reset WiFi before attempting reconnection.

Spot Cleaning

In the Standby or Pause mode, press and hold the button to start spot cleaning. This mode is used to clean a 1.5m x 1.5m square area centered on the robot. After cleanup, the robot will return to the center of the square.

Note: Pressing any button will cancel the current spot cleaning cycle.

Note:

• A full map must be created and Map Saving mode switched on before this function can be used.
• After cleaning starts, the robot may move beyond the defined areas. Make sure there are no obstacles preventing the robot's access to the target rooms.

Pin n Go

Use the APP to set a destination for the robot to go to.

Cleaning mode

Use the APP to choose from Quiet, Balanced, Strong, or MAX modes. Balanced mode is the default.

Do Not Disturb (DND) mode

In DND mode, no cleanups will start, no voice alerts will play, and the power indicator will dim. DND mode set from 22:00 to 08:00 by default and can be disabled or modified in the APP.

No-go zones / Invisible Wall / Mopping No-Go Zone

The app can be used to draw Virtual No-Go Zones and Walls, as well as Virtual No-Mop Zones and Walls to keep the robot from entering the areas you define. Virtual No-Mop Zones and Walls are only activated when the mopping cloth bracket is installed.

Note:

• "Map Saving Mode" must be turned on in the app to use virtual no-go zones.
• Virtual no-go zones and walls should only be used to customize the cleaning area. They should not be used to isolate hazards.
• Moving the robot manually or making significant changes to the home environment may cause the loss of Virtual No-Go Zones and Walls.
  

More app functions

Note: Functions and details of the app may vary slightly due to continuous app development and upgrades.

Refilling the water tank or cleaning the mopping cloth midway

To refill the water tank or clean the mop cloth during a cleanup, pause cleaning by pressing any button and remove the mop module. Refill the water tank and/or clean the mop cloth as required. Reinstall the mop module and press the button to continue cleaning.

Charging dock

The charging dock should be plugged in and placed against a wall on level ground, with more than 0.5m (1.6ft) of clearance on each side, and more than 1.5m (5ft) in front. For the best experience when using the mobile app, place the charging dock in an area with strong WiFi coverage.

Note: Do not place the charging dock in direct sunlight or block the locator beacon; otherwise, the robot may not be able to return to the charging dock.

Routine maintenance

Main brush

* Clean weekly

1. Turn the robot over then unlatch and remove the main brush cover.
2. Take out the main brush, remove and clean its bearings.
3. Remove the main brush cap, rotating in the unlock direction.
4. Use the supplied main brush cleaning tool to remove any entangled hair.
5. Re-install the cap and bearings following the lock direction.
6. Re-insert the main brush and replace the brush cover.

Note: Main brush replacement every 6-12 months is recommended.

Using the main brush cleaning tool

Use the main brush cleaning tool to remove any hair entangled around the main brush.

Note: If there is a large amount of hair, or hair is tightly entangled, remove it carefully to avoid damage to the main brush.

Dustbin and filter

* Weekly cleaning is recommended

1. Open the top cover of the robot, squeeze the dustbin latch, and remove the dustbin.
   
   
2. Open the dustbin lid as indicated by the arrow and pour out the contents.
   

Clean the washable filter

* Clean every two weeks

1. Open the dustbin lid as indicated by the arrow and pour out the contents.
   
   
2. Fill the dustbin with clean water and close the cover. Gently shake the dustbin, then pour out the dirty water.
   
   Note:
   Only use fresh water without cleaning liquid.
3. Remove the filter and clean it with water.
   
   Note:
   To avoid damage, do not touch the surface of the filter with hands, brushes, or sharp objects.
4. Rinse repeatedly and tap the filter frame to remove as much dirt as possible.
   
   
5. Leave the filter to dry before reinstalling it.
   Note:
   Allow the filter to dry thoroughly before use. 24-hours of drying is recommended.

Battery

The robot is equipped with a high-performance lithium-ion rechargeable battery pack. To maintain battery performance, keep the robot charged.

Note: If the robot is to be left unused for an extended period, turn it off before storage and charge it at least once every three months to avoid battery damage resulting from over-discharging.

Charging dock

* Monthly cleaning recommended

Use a soft dry cloth to clean the charging contacts of the charging dock.

Side brush

* Monthly cleaning recommended

1. Turn the robot over and remove the screw holding the side brush.
2. Remove and clean the side brush.
3. Reinstall the side brush and tighten the screw.
   
   Note:
   Side brush replacement every 3-6 months is recommended.

Water tank

* Frequent cleaning is recommended

1. Open the water tank.
2. Fill the filter with water
3. Shake it, and pour out the water

Mop cloth

* Clean after use

1. Remove the mop cloth from the mop cloth bracket.
   
   
2. Clean the mop cloth and dry it.
   Note:
   • If the mop cloth gets excessively dirty, cleaning quality will be affected. Cleaning it before use is recommended.
   • Replacing the mop cloth every 3-6 months is recommended to maintain cleaning quality.

Omnidirectional wheel

* Frequent cleaning is recommended

1. Turn the robot over.
2. Use a small screwdriver to separate the axle and the tire.
3. Rinse the axle and tire with water to remove any hair and dirt.
4. Dry and rebuild the wheel, then press it back in place.
   
   Note:
   The omnidirectional wheel bracket cannot be removed.

System Reset

If the robot does not respond when you press a button or the robot cannot be shut down, press the Reset button. The robot will then restart.

Note: After a system reset, cleaning schedules, WiFi and other settings will be restored to factory settings.

Restore factory settings

If the robot is not functioning after a system reset, turn it on, then press the Reset button. Then press and hold the button until you hear the "Start restoring initial version" voice alert. The robot will then be restored to factory settings.

Machine sensors

* Monthly cleaning recommended

Use a soft dry cloth to wipe and clean all sensors, including:

1. Four cliff sensors at the bottom of the robot.
2. The wall sensor on the right of the robot.
3. The charging contact on the bottom of the robot.
   

Firmware update

Update the robot using the app. Place the robot on the charging dock and ensure that the battery level is higher than 20% before updating. The power indicator will flash white quickly during a firmware update.

Holiday Energy Saving Function

When the robot is docked, press and hold "Recharge" for seconds or until you hear an alert sound. This will activate Holiday mode. In this mode the robot will switch to Low Power mode to minimize power consumption. This includes a dimming of the LED indicator, and the stopping of all non-charging related functions including cleaning, remote control over WiFi, and more. To deactivate Holiday mode, press and hold "Recharge" for seconds until the LED indicator brightens.

Basic parameters

Robot

Charging dock

Note: The serial number is on a sticker on the underside of the robot.

Troubleshooting

If an error occurs during cleanup, the power indicator will flash red quickly, and a voice alert will play. Refer to the table below for resolution options.

Note: A system reset may not resolve all problems.

If the problem persists after using the recommendations in the table above, please email our after-sales service team:
US/Non-Europe Support: support@roborock.com
Europe Support: support@roborock-eu.com

FAQs

Robot Vacuum Cleaner
Manufacturer: Beijing Roborock Technology Co.,Ltd.
Product Model: roborock S5 Max
Address of Manufacturer: Floor 6, Suite 6016, 6017, 6018, Building C, Kangjian Baosheng Plaza,
No.8 Heiquan Road, Haidian District, Bejing, P.R.CHINA

For more product information, visit our website: www.roborock.com
For after-sales support, email our after-sales service team:
US/Non-Europe Support: support@roborock.com
Europe Support: support@roborock-eu.com

Videos

Roborock S5 Max Review Video

Roborock S5 Max Mopping Test Video

Documents / Resources

References

• Roborock US Official Site | Intelligent Robot Vacuum Cleaner and Mop
• App Store - Apple
• Google Play

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Roborock S5 MAX Manual